B and W Turnoverball Gooseneck Hitch that Fits 2001 Chevy Silverado

Question

Question:

Will a BWGNRK1059 work in a 99 chevy silverado 2500?? It calls for a BWGNRK1067-5W but is the a big difference

asked by: Jeremiah R

0

Expert Reply:

For your 2001 Chevy Silverado the part # BWGNRK1067 that you mentioned is a fit if you have a 2500HD that is short or long bed. The part # BWGNRK1059 instead fits the 1500 and 2500 LD models so it would be based on your specific truck setup.

expert reply by: Jameson C

0

Answer 1

If you have the center section of a B and W Turnoverball Gooseneck hitch already but need the hitch part #BWGNRK1067 all you need for the rails is the #BWGNRM1067 which is just the rails of that hitch kit.

view full answer...

Answer 2

I was able to find that your 2003 Chevy Silverado with a Duramax diesel engine has a towing capacity of 12,000 lbs.

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

I definitely understand being a bit overwhelmed by the amount of options in front of you, however I can definitely help with differentiating the trailer hitches for your 2019 Subaru Outback Wagon along with explaining my personal recommendation,…

view full answer...

B and W Turnoverball Gooseneck Hitch that Fits 2001 Chevy Silverado

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching