Availability of Rail Kit for B and W Turnoverball Fifth Wheel Hitch BWGNRK1067

Question

Question:

Can I purchase just the side plates for the hitch I have a complete setup for a 1500 but need a 2500hd setup

asked by: Jeremy

0

Expert Reply:

If you have the center section of a B and W Turnoverball Gooseneck hitch already but need the hitch part # BWGNRK1067 all you need for the rails is the # BWGNRM1067 which is just the rails of that hitch kit.

expert reply by: Jameson C

0

Answer 1

The side plates by themselves are not something that can be purchased separately. So to get the side plates you would need to get the entire installation kit, the B&W Turnoverball Gooseneck Custom Installation Kit for Chevy/GMC #BWGNRM1067.

view full answer...

Answer 2

The B&W Turnoverball gooseneck hitches are different parts for a 2013 Chevy Silverado 2500 and a 2008 Chevy Silverado 2500. Both the center sections and the installation kits are different, and I'll list the hitches that fit both…

view full answer...

Answer 3

For your 2001 Chevy Silverado the part #BWGNRK1067 that you mentioned is a fit if you have a 2500HD that is short or long bed. The part #BWGNRK1059 instead fits the 1500 and 2500 LD models so it would be based on your specific truck setup.

view full answer...

Answer 4

I was able to find that your 2003 Chevy Silverado with a Duramax diesel engine has a towing capacity of 12,000 lbs.

view full answer...

Answer 5

Because the one truck is a 2500 and the other is a 1500 the two would not share the same gooseneck fits. For the 2009 Silverado 1500 you would need the part #BWGNRK1057. I attached an install video for more info for you to check out as well.

view full answer...

Answer 6

My B&W representative tells me that the 2007 Silverado (New Body or Classic Model) use a different Turnover Ball Hitch than the 2008 Silverado 2500. But, the good news is that instead of getting a whole new hitch, you can retain the center…

view full answer...

Answer 7

B and W has the part #BWGNRK1062 as a fit for the 3500 long bed models of the 2007 Chevy Silverado and the #BWGNRK1067 as a fit for the 2500HD models. The bracket designs are quite a bit different and it looks like the holes in the truck frames are…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Availability of Rail Kit for B and W Turnoverball Fifth Wheel Hitch BWGNRK1067

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching