Will Curt 14017 Fit 2018 Ford F-150 FX4

Question

Question:

I have 2018 ford fx4 4x4 pickup? Looking at your trailer hitches. Does C14017 fit my truck? How easy are they to install? Thanks

asked by: Pam

0

Expert Reply:

The Curt # C14017 will fit your 2018 Ford F-150 FX4 as long as you do not have a factory hitch installed. This is a fairly simple installation, we give it a 4 out of 10 for difficulty with a 40 minute install time. No cutting or drilling is required and it uses a simple-bolt on installation. You will have to remove or lower the spare tire temporarily. I have attached an installation video so you can see what the process is like.

expert reply by: Robin H

0

Answer 1

We only have one hitch available that fits your 2015 Ford F-150 that has a factory hitch with the Curt Class IV part #C26HR which has a 10,000 lb trailer weight capacity if not using weight distribution or 12,000 lbs if using a WD system.

view full answer...

Answer 2

From my research regardless of how your truck is equipped you should have no problem meeting the 5,000 pound minimum because the lowest rated F-150 from 2017 has a towing capacity of 7,600 pounds. The exact capacity of your F-150 depnds on some other…

view full answer...

Answer 3

The Curt hitch #C26HR is a great higher capacity trailer hitch for your 2018 Ford F-150 Raptor as it is rated for up to 10,000 lb trailer weight. This fits if you have the factory hitch which it sounds like you have. If you instead didn't have…

view full answer...

Answer 4

Curt has a hitch that does fit your 2018 Ford F-150 with a factory hitch with the part #C26HR which fits below the factory hitch, but the part #C14017 does not fit versions of your truck that do have the factory hitch.

view full answer...

Answer 5

The Curt Trailer Hitch Receiver part #C14017 and Curt Trailer Hitch Receiver part #C26HR (C14021) which are both fits for a 2015 Ford F-150 are designed for models with a factory rear bumper. That said, they are also both fits for Raptor models so if…

view full answer...

Answer 6

The appropriate fishwire is included with the Curt Trailer Hitch Receiver #C26HR that fits your 2021 Ford F-150 without a factory hitch. I have added a cut out from the installation instructions for you which show the parts included. So the hitch…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

I looked up your Dexter 8-222 Hub and was able to find the inner and outer bearing numbers as well as the grease seal used. It looks like this particular hub was designed for mobile homes and these, for the most part, have more unique bearings and…

view full answer...

Answer 10

Yes the Replacement Brass Connector #T4750300 for Titan Disc Brake Actuators will fit a Tie Down 660e disc brake actuator.

view full answer...

Answer 11

To replace your AL-KO 568303 seal you will want the Oil Seal #91030. This seal has the same inner diameter of 2.750 inches and outer diameter of 3.779 inches. It is a confirmed fit for your #99 spindle that uses the AL-KO 568303 seal.

view full answer...

Answer 12

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Will Curt 14017 Fit 2018 Ford F-150 FX4

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching