Best Trailer Hitch Receiver For a 2022 Ford Bronco Sport

Question

Question:

Which receiver is best for my 2022 Ford Bronco Sport?

asked by: DJ

0

Expert Reply:

I recommend the etrailer Trailer Hitch Receiver # e57KR as being the best receiver for your 2022 Ford Bronco Sport. This receiver is custom fit and has a matte black finish to give it the factory appearance. It features a lifetime warranty and is made in the USA.

The T-One Vehicle Wiring Harness # TK46FR connects in line of your factory tail lights to give you a 4-way flat connector. This is needed to connect to the lights on most small trailers you might tow and can also be used with Auxiliary Lights # C53201.

expert reply by: Bud M

0

Answer 1

The instructions for the Curt Trailer Hitch Receiver #C76HR provide a diagram showing where to trim the fascia. There is no actual template to follow, so correctly marking and cutting the fascia is ultimately up to you. Looking at the installation…

view full answer...

Answer 2

Good question, and there is just one difference between the Curt and etrailer trailer hitches that fit your 2022 Ford Bronco Sport, and that's their finish. The Curt hitch has a glossy black finish while the etrailer hitch has a matte black…

view full answer...

Answer 3

I recommend the etrailer Trailer Hitch Receiver #e57KR for your 2022 Ford Bronco Sport. This receiver has a hidden cross tube and matte black finish giving it a clean factory appearance. The receiver is rated for up to 525lbs of tongue weight and…

view full answer...

Answer 4

We do indeed offer a 4-pole trailer wiring harness for your 2022 Ford Bronco Sport. I'd recommend the Tekonsha T-One harness, part #TK46FR. If you click the provided link, you can see an installation video.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...