Trailer Hitch Recommendation for Towing with 2018 Lexus RX 350 F Sport

Question

Question:

I want to install a hitch on my 2018 RX350 F-Sport for a small cargo trailer. I like the Draw Tite over the Curt because of the 4500 lb. vs. the 4000 lb. capacity. However the listing on both hitches states excluding F Sport. But after watching the video and reading the comments and questions I dont see why it wouldnt work. Will the Draw Tite 75540 work on my car or not?

asked by: DAVID M

0

Expert Reply:

Yes, the Draw-Tite Max-Frame Trailer Hitch Receiver # 75540 will fit your 2018 Lexus RX 350 F Sport. We have it listed as fitting the F Sport as well as models aside from the F sport which is why the listing can be confusing some when looking at the product page.

To complete your towing setup I also recommend picking up the Tekonsha T-One # 118255 if you don't have the tow package or the T-One # 118252 if you do have the tow package. Then you can secure the wiring to the hitch you'll use the Mounting Brackets # C57202 and # 18144.

For a ball mount kit I recommend checking out the etrailer Kit # EBMK4.

Attached are some videos for you to reference.

expert reply by: Jon G

0

Answer 1

There is a trailer hitch receiver that my contact at Draw-Tite was able to confirm will fit your 2021 Lexus RX 350 F-Sport which is the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" #75540. The #75540 has a hidden…

view full answer...

Answer 2

I'm assuming that you're needing to know so you can choose the correct wiring harness, correct? You could call your Lexus dealer and give them your VIN, and they should be able to tell you how your RX350 is equipped. Or, you could remove the…

view full answer...

Answer 3

According to Curt, the Curt Hitch #C73DR will not fit the F-Sport version of your 2021 Lexus RX350. In fact, we do not currently have a hitch that is compatible with your Lexus. Even all of our trunk bike racks have been excluded due to the spoiler.…

view full answer...

Answer 4

I have taken a look at the Draw-Tite Max-Frame Trailer Hitch Receiver item #75540. This hitch is confirmed to fit your 2022 Lexus RX 350 and it does require some minor trimming of the lower portion of the rear trim. I have linked a couple of pictures…

view full answer...

Answer 5

I checked with Curt and theCurt Trailer Hitch Receiver part #C73DR they said it is as a fit for all models of the 2016 Lexus RX 350 EXCEPT the F Sport package. so no, it will fit not work for you. However, we have just what you need. You can use the…

view full answer...

Answer 6

Both of the trailer hitches that fit your 2018 Lexus RX 350 will give you the same amount of clearance. The etrailer #e94AR and Curt #C13272 that fit your Lexus each have approximately 15-1/2 inches of clearance from the ground to the top of the…

view full answer...

Answer 7

Yes we do! For your 2018 Lexus RX 350 F-Sport model we have the Curt Class III Receiver Hitch #C13272. This is currently the only hitch available that is confirmed to fit the F-Sport model. It will install by using existing holes in the vehicle's…

view full answer...

Answer 8

If your Lexus RX350 already has the tow package which provides the taillight converter that's plugged into the connector located behind the passenger side cargo area bulkhead as shown in the linked instructions, you'll just need the #118252…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...