Crosstube Width on Ultra Frame Trailer Hitch Receiver 41947

Question

Question:

Looking for how wide it is from side to side where the 4 bolts go into side plates?

asked by: Thomas J

0

Expert Reply:

The width of the Ultra Frame Trailer Hitch Receiver part # 41947 is 30-1/2" from the outside of each side plate. If you subtract the thickness of the plates you're looking at around 30" from end to end on the crosstube.

expert reply by: Conner L

0

Answer 1

Draw-Tite trailer hitch #41947 is a custom fit hitch designed for specific vehicles and should not be used on any applications it was not designed for. The trucks it does fit on would have approximately 37 inch frames measured from outside to…

view full answer...

Answer 2

Draw-Tite custom-fit Class V hitch #41947, which fits trucks with an outside-to-outside frame width of 34-inches, can be installed at any of three heights, thanks to the multiple holes in the two frame brackets. I can give you these heights…

view full answer...

Answer 3

The horizontal mounting plate that mounts to the frame of your vehicle on the #41947 is 2-13/16" wide and the mounting plates themselves are 11-9/16" tall. The holes on the horizontal mounting plates are 3/4" and 1-1/4" in…

view full answer...

Answer 4

I have attached an image of the Draw-Tite Ultra Frame Trailer Hitch Receiver #41947 referenced in your question with a few dimensions labeled. The distance between mounting holes, from the left side mounting bracket to the right side mounting bracket…

view full answer...

Answer 5

I have attached an image of the Draw-Tite Ultra Frame Trailer Hitch Receiver #41947 referenced in your question with a few dimensions labeled. The distance between mounting holes, from the left side mounting bracket to the right side mounting bracket…

view full answer...

Answer 6

The Draw Tite hitch part #41947 has been confirmed as a fit for your 1999 Chevy 3500 that is built on a cab and chassis frame that is 34 inches apart. It has the cutout in the mounting flange to clear the spring hanger like you said you needed as…

view full answer...

Answer 7

Yes we do, it can be found listed as part #41947 on our site and is confirmed by Draw-Tite to fit your 2005 Chevrolet Kodiak C5500 Chassis with a Motorhome on it.

view full answer...

Answer 8

I reached out to Draw-Tite and found that the distance from the frame mounting point to the top of the receiver at the lowest setting is 10-5/16". Keep in mind, the Ultra Frame Trailer Hitch Receiver #41947 is only confirmed to fit C/K series…

view full answer...

Answer 9

Since you have a 34 inch wide frame we may have something that could work with a bit of fabrication on your part. 34 inch wide frames (measured from outside to outside) is a very common frame width for cab and chassis trucks. Check out the part…

view full answer...

Answer 10

I am going to need a bit more information in order to make a good recommendation. Is your 2010 Ford E450 a Cab and Chassis style or an RV cut-away. I spoke with my contact at Cequent, and they said that what you would have to do to determine if a…

view full answer...

Answer 11

I have a universal hitch that will fit your Gulf Stream and provide you with the needed 10,000 lbs towing capacity but it must be welded on. It is the Class V Universal Weld-on Receiver Hitch item #15901. None of the bolt on hitches have a capacity…

view full answer...

Answer 12

The Ultra Frame Trailer Hitch Receiver #41947 has an adjustable cross-tube that allows the receiver to be moved into a variety of height adjustments. There are 3 locations on that this hitch can be mounted in (see attached photo diagram): Height from…

view full answer...

Crosstube Width on Ultra Frame Trailer Hitch Receiver 41947

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching