Availability of the Draw-Tite Trailer Hitch Receiver # 41947 For a 2005 Chevy Kodiak C5500 Chassis

Question

Question:

Do you carry/sell the Draw-Tite ultra-frame hitch #41947 for my 2005 Chevy Kodiak C5500 motorhome chassis?

asked by: James R

0

Expert Reply:

Yes we do, it can be found listed as part # 41947 on our site and is confirmed by Draw-Tite to fit your 2005 Chevrolet Kodiak C5500 Chassis with a Motorhome on it.

expert reply by: Jon G

0

Answer 1

The 2017 GMC Sierra 3500 cab-and-chassis is a confirmed fit for the Draw-Tite Ultra Frame Trailer Hitch #41947 so long as the truck frame width dimension is 34-inches from outside edge to outside edge. This frame dimension requirement applies to…

view full answer...

Answer 2

The linked instructions for the custom-fit Draw-Tite Ultra-Frame Class V hitch #41947 show specific height dimensions from the bottom of the vehicle frame down to the top of the hitch receiver tube. The adjustable side brackets can place the…

view full answer...

Answer 3

I have attached an image of the Draw-Tite Ultra Frame Trailer Hitch Receiver #41947 referenced in your question with a few dimensions labeled. The distance between mounting holes, from the left side mounting bracket to the right side mounting…

view full answer...

Answer 4

A factory 7-way trailer connector isn't all you need to power a trailer's electric brakes. You still need a brake controller. Some Ford F-150s are equipped with a factory integrated brake controller, which you may have. If your 2012 Ford…

view full answer...

Answer 5

Draw-Tite custom-fit Class V hitch #41947, which fits trucks with an outside-to-outside frame width of 34-inches, can be installed at any of three heights, thanks to the multiple holes in the two frame brackets. I can give you these heights…

view full answer...

Answer 6

The Ultra Frame Trailer Hitch Receiver #41947 has an adjustable cross-tube that allows the receiver to be moved into a variety of height adjustments. There are 3 locations on that this hitch can be mounted in (see attached photo diagram): Height from…

view full answer...

Answer 7

I am going to need a bit more information in order to make a good recommendation. Is your 2010 Ford E450 a Cab and Chassis style or an RV cut-away. I spoke with my contact at Cequent, and they said that what you would have to do to determine if a…

view full answer...

Answer 8

I have a universal hitch that will fit your Gulf Stream and provide you with the needed 10,000 lbs towing capacity but it must be welded on. It is the Class V Universal Weld-on Receiver Hitch item #15901. None of the bolt on hitches have a capacity…

view full answer...

Answer 9

Since you have a 34 inch wide frame we may have something that could work with a bit of fabrication on your part. 34 inch wide frames (measured from outside to outside) is a very common frame width for cab and chassis trucks. Check out the part…

view full answer...

Answer 10

I have attached an image of the Draw-Tite Ultra Frame Trailer Hitch Receiver #41947 referenced in your question with a few dimensions labeled. The distance between mounting holes, from the left side mounting bracket to the right side mounting bracket…

view full answer...

Answer 11

The width of the Ultra Frame Trailer Hitch Receiver part #41947 is 30-1/2" from the outside of each side plate. If you subtract the thickness of the plates you're looking at around 30" from end to end on the crosstube.

view full answer...

Answer 12

The horizontal mounting plate that mounts to the frame of your vehicle on the #41947 is 2-13/16" wide and the mounting plates themselves are 11-9/16" tall. The holes on the horizontal mounting plates are 3/4" and 1-1/4" in…

view full answer...

Availability of the Draw-Tite Trailer Hitch Receiver # 41947 For a 2005 Chevy Kodiak C5500 Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching