How to Convert 2K etrailer Trailer Axle with Idler Hubs to Overslung Configuration

Question

Question:

Question on your Item # e82GR 2000lb trailer axle. Is there anyway to get it in a over slung configuration or will I need to get the Dexter Trailer Springs Over-Under Conversion Kit to do it myself. Im looking at acquiring this for a lite off road diy tear build i am doing. Any help is appreciated.

asked by: Don K

0

Expert Reply:

The Trailer Axle with Idler Hubs # e82GR only comes in the underslung configuration. In order to place the springs on top of the axle you'll actually need to have a professional welder install the spring seat # TRSS175 on top of the axle as Dexter Axle only makes their conversion kit for 2-3/8" and 3" diameter axles.

If you're wanting the axle to come with the spring seats welded on top of the axle then you'll need to reach out to your local trailer shop or dealer to see if they'd be able to order one in this configuration for you.

expert reply by: Jon G

0

Answer 1

In order to find a replacement axle for your Harbor Freight trailer you will need to take some measurements to determine the correct axle length. The most important measurement is the distance from hub face to hub face. Additionally, you can measure…

view full answer...

Answer 2

For a standard axle we have the Trailer Axle with Idler Hubs - 4 on 4 Bolt Pattern #e25GR which is rated for 2,000 lbs but the spring seats are 48" apart on center so for this to fit you'll have to cut off the current sets and have new ones,…

view full answer...

Answer 3

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 4

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 9

Since Grand Design is kind enough to list certain parts for their trailers I can confirm you have a 33" wheelbase on your 2020 Grand Design Transcend 27BHS. This means the MORryde Rubber Equalizers #MR87ZR will fit your trailer. Although I'm…

view full answer...

Answer 10

Hey Jaime, yes you can replace your 25-1/4 inch 3,500 lb axle leaf springs with a 5k rated axle spring like the part #e44SR. This will increase the suspension's weight capacity and might make the ride quality a little rougher but it would fit and…

view full answer...

Answer 11

Good question, and what happens is that leaf springs elongate over time, and since you mentioned you got measurements of 25-1/2 inches from center eye to center eye and 26 inches under partial load, the best option for leaf springs really is the…

view full answer...

Answer 12

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...