Replacement Threaded Anti-Rattle Hitch Pin Bolt for Curt Premium 5 Bike Rack

Question

Question:

What is the correct threaded hitch lock for this CURT bike rack? The shaft is less than 1/2 inch. See picture attached. This is the threaded bolt on the18065 bike rack.

asked by: Mariano R

0

Expert Reply:

To replace the threaded anti-rattle bolt for your Curt Premium 5 Bike Rack for 2" Hitches # C18065 we have the SportRack Locking Anti-Rattle Bolt # SR0901. Curt doesn't make a replacement bolt for their bike rack but we have confirmed that this is the only one we carry that is compatible with the threads on your bike rack.

expert reply by: Jon G

0

Threaded Anti-Rattle Hitch Pin Bolt for Curt Premium 5 Bike Rack
(click to enlarge)

Answer 1

Bike rack manufacturers make their threaded hitch pins/locks and threaded rack shanks uniquely threaded so you would not be able to use one brand of lock with another brand bike rack. The best solution to lock the Curt bike rack #C18065 is to use a…

view full answer...

Answer 2

The Curt Bike Rack part #C18065 does include a threaded hitch pin bolt that will tighten the shank of the rack to the hitch that the rack is installed in. For a lock that you could run through the end of the bolt after it is installed you could use…

view full answer...

Answer 3

Curt does not offer the straps for the bike rack but I do have a solution for you. I recommend the Replacement Strap, part #853-2569. This strap measures 9-3/8 inches long and the holes measure 1 inch center to center. The only difference I could see…

view full answer...

Answer 4

You wouldn't be able to use the Swagman lock on the Curt bike carrier. Bike rack manufacturers thread the bolts and shanks uniquely so that you can't use competitors products. There are some one-off exceptions but since they are not tested…

view full answer...

Answer 5

Absolutely! For your Curt Premium 5 Bike Rack for 2" Hitches - Tilting #C18065 I recommend the Anti-Rattle Hitch Lock for SportRack Bike Racks and Cargo Carriers - 1-1/4" and 2" Hitches #SR0901 which includes a new anti-rattle bolt and…

view full answer...

Answer 6

I have a solution for you, but the etrailer #e99047 is not a confirmed fit on the Curt bike racks. Instead, we have confirmed that the The SportRack Anti-Rattle Hitch Lock for SportRack Bike Racks and Cargo Carriers - 1-1/4" and 2" Hitches…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

To me it makes the most sense to put a Bike Rack #HLY64FR on the flat towed vehicle rather than above the tow bars. Especially on heavy e-bikes as they are difficult to lift that high onto the rack, but also as it only makes sense to have the rack on…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The Tow Defender #RM-4700 you found is really our best option to protect the front of your 2024 Chevrolet Trax. This screen helps to deflect any road debris back down to the ground to keep it traveling under your Trax. This particular cover is…

view full answer...

Answer 12

Just looking at your Tern HSD bike with fenders, I'm going to say no the Saris MHS Bike Rack for 1 Bike #SAR23MR is not going to work. I did some research and it looks like a lot of Tern owner's went with the Hollywood Racks Sport Rider SE…

view full answer...