Replacement Wobble Rollers 5 Diameter, 3 Wide For a 3/4 Shaft

Question

Question:

I have a 1984 shoreline boat trailer with 32- 5 od ×3 width, with a7/8 hub width at the center. they are mounted on 3/4 dia shafts. Do you carry replacement rollers in rubber or polyurethane? Thanks,

asked by: Charlie M

1

Helpful Expert Reply:

We have the Yates Ribbed Wobble Roller in either a Heavy-Duty Rubber # YR530R-6P or Thermoplastic Rubber # YR500YW-6P. These both are 5" in diameter, 3" wide and fit on a 3/4" shaft. These will both have a 7/8" hub diameter.

We do also carry the 3/4" Wobble Roller Washer # CE10983, Wobble Roller Retainer Ring # CE10981 and Angled Hog Ring Pliers # PTW88003. These will allow you to replace any missing damaged or worn parts you may need.

expert reply by: Bud M

1

Answer 1

I have a solution that might work for you, but the length of the bearing and bushing on the Yates Wobble Roller #YR530R-6P is 1-1/2", so it's going to be the same as the ones you've currently got. You might want to look at the Yates…

view full answer...

Answer 2

The hub length of the CE Smith Ribbed Wobble Roller for Boat Trailers part #CE29536 is 3/4" per the manufacturer.

view full answer...

Answer 3

I went out to the warehouse and measured Yates wobble roller #YR530R-6P. The width of the center is 1-5/8 inches so it will be too large. Your best option is going to be roller #YR440R which is much narrower but the overall width is 4-1/4 inches. The…

view full answer...

Answer 4

Looks like you have the Yates Ribbed Wobble Rollers part #YR530R-6P installed on your Shoreline boat trailer. We do not carry any pieces that are internal of the roller like a bushing if that is what you are referring to. We carry the retainer rings…

view full answer...

Answer 5

Yes, there is an inner washer then the Yates Ribbed Wobble Roller #YR530R-7P, outer washer and finally the Hog Ring Retainer #CE10981. We do have the Angled Hog Ring Pliers #PTW88003 to aid in the installation of the retainers. You may also consider…

view full answer...

Answer 6

We have a few options for replacement rollers that fit 3/4" roller shafts. The Yates Ribbed Wobble Roller #YR530R-6P is 3" wide, 5" in diameter, and fits 3/4" shafts. The Yates Ribbed Wobble Roller #YR343R-6P is also 3" wide…

view full answer...

Answer 7

I may have a solution for you, but we don't carry Shoreline brand parts. With that said, you might be able to use something like the Yates Ribbed Wobble Roller #YR530R-6P, which is 5"diameter and 3" wide. This wobble roller has a…

view full answer...

Answer 8

For a 5 inch diameter by 3 inch wide wobble roller that has a 3/4 inch diameter shaft you would want the part #YR530R-6P.

view full answer...

Answer 9

The roller bunks part #DL21754 are designed to fit on the end of a 2x4 board so the width of the channel is 1-1/2 inches.

view full answer...

Answer 10

In order to get your wobble rollers rolling again I have two recommendations. The first is to attempt to pull them off and clean them, then use grease to free up the movement. Another possibility is that the shaft is bent. You should be able to bend…

view full answer...

Answer 11

The closest option we have to the dimensions you listed for your existing rollers is the CE Smith Ribbed Wobble Rollers #CE29210. These will fit your 1-1/8" shaft but they feature a 5" diameter and a 3" width, varying slightly from…

view full answer...

Answer 12

It sounds like you are needing replacement rollers like the CE Smith Ribbed Wobble Rollers for Boat Trailers - Rubber - 3/4" and 1-1/8" Shafts - Qty 4 #CE29210. If you don't have the wobble style rollers, then I recommend the bunk…

view full answer...

Replacement Wobble Rollers 5 Diameter, 3 Wide For a 3/4 Shaft

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching