Recommended Trailer Hitch For A 2010 Mazda CX-9 Using A Thule Trailway 4 Bike Rack

Question

Question:

Which etrailer hitch works best with a Thule Trailway 4 bike rack when attached to a 2010 Mazda CX-9 SUV? Also, what additional items should I purchase to improve the safety, transport and security of the bikes?

asked by: Chuck A

0

Expert Reply:

When it comes to installing a trailer hitch on your 2010 Mazda CX-9 I recommend The etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2 inch # e98AR. This hitch will work perfect with your Thule Trailway bike rack.

The hitch has a tongue weight up to 400 pounds. The hitch has a bolt-on installation with no welding required and has a matte black powder coat finish over a protective base coat that offers a superior rust resistance.

To keep your bike rack snug and locked onto the hitch during travel The Thule Snug Tite Hitch Lock and Anti-Rattle Device # THSTL2 would work well for you. This system has an integrated dust cover that keeps the lock clean. This lock will work on both 1-1/4 inch and 2 inch Thule hitch mounted racks. It has a 1/2 inch pin diameter with an overall pin length of 4-1/2 inches.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

That is an excellent idea and exactly what I've done with my vehicles as well so I definitely get where you're coming from. I recommend the following parts for your 2015 Mazda CX-9: - etrailer Trailer Hitch Receiver #e98AR - Curt T-Connector…

view full answer...

Answer 2

I did a little research and found that the towing package for the 2010 Mazda CX-9 includes: 1. A heavy duty transmission oil cooler and radiator fan 2. A revised engine control module (probably means that the computer has been programmed to be more…

view full answer...

Answer 3

The Trailway sold in the big box stores is the same thing as the Hitching Post Pro, #TH934XTR, both of which are similar to the Parkway. The straps are all the same too. But the Trailway and Hitching Post are more related to each other since they are…

view full answer...

Answer 4

The best way to run the power wire for this Tow Ready Custom Fit Vehicle Wiring, part #118520, on your 2011 Mazda CX9 would be to run the wire through either a grommet in the trunk area to the exterior of your vehicle and then along a frame rail…

view full answer...

Answer 5

Other than the difference in brand/manufacturer, the Curt #13575 and the Draw-Tite #75531 for your Mazda CX-9 are pretty close to identical. Between the two options I do recommend the Curt Trailer Hitch #13575 because the hitch itself is made in the…

view full answer...

Answer 6

The Curt hitch part #13575 when installed does change the spare tire access but you still will be able to access the spare tire when needed. Basically you'll have to push the spare around the hitch as you raise or lower it. We've had…

view full answer...

Answer 7

The most common cause for some trailer light functions to operate while others do not is a bad ground connection at either the vehicle wiring harness or the trailer-side wiring. This can happen because a weak ground will still allow some current to…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...