Recommended Trailer Hitch For A 2014 Chevrolet Tahoe

Question

Question:

say police package will fit all 2 wd tahoes??

asked by: Todd

0

Expert Reply:

When it comes to installing a trailer hitch on your 2014 Chevrolet Tahoe The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2 inches # C13161 is confirmed to fit all 2wd Tahoes.

This trailer has a bolt-on installation with no welding required. It has a gloss black powder coat finish which is over a protective base coat which offers superior rust resistance. The trailer hitch has a maximum gross trailer weight up to 6,000 pounds and has a maximum tongue weight up to 600 pounds. I would recommend checking your vehicle's manual to double check the proper towing capacity for your vehicle.

The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118384 will make your vehicle have a four flat trailer connector. Using this harness will make your trailer's brake, stop, and turn lights mirror your vehicle's brake, stop, and turn lights. This harness plugs into your vehicle's wiring harness, which is located behind the rear bumper. Once installation is complete, the 4-way flat connector will be stowed beneath your vehicle, near the trailer hitch. The Mounting Bracket # 18144 is recommended to keep the connector secure.

I attached a review video link below.

expert reply by: Noah E

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 6

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 10

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...