Fitment of Replacement Rubber Grommet for RV Black Water Tanks, # F02-2106

Question

Question:

This gasket is for connecting a toilet to a black water tank, I think I got that part right. Problem, my tank is 3/8 inch thick, and the groove on this grommet looks to be about 3/16 inch, where the grommet slides onto the top of the tank. The difference in thickness of the groove and the thickness of the tank would not provide a good seal. Are there grommets that have a wider groove for thicker tanks? Thank you.

asked by: Richard A

1

Helpful Expert Reply:

The grove of the replacement Rubber Grommet for RV Black Water Tanks, # F02-2106 that you linked to is about 1/4". If your tank is 3/8", this will work, providing a tight seal.

expert reply by: Michael R

1

Answer 1

In order to help prevent leaking between the grommet and tank on the Replacement Rubber Grommet for RV Black Water Tanks part #F02-2106 it would be wise to use a sealant like part #LT37467 between the two surfaces. I am not sure if this is a…

view full answer...

Answer 2

If your RV black water pipe is threaded, we have an adapter that may give you the additional length you're looking for. The LaSalle Bristol Toilet Flange, part #3446336347, has a spigot end. The Valterra DWV Adapter, part #D50-2929, converts a…

view full answer...

Answer 3

This is an unexpected configutation with the valve connected directly to the black tank. Nevertheless, it seems that a Valtera #F02-2106 Replacement Rubber Grommet would fix you right up. I think I would spring for some new Valterra #H03-0018 hose…

view full answer...

Answer 4

The LaSalle Bristol Toilet Floor Flange w/ Spigot for RV - ABS Plastic - 3" Hub x 4" Diameter #3446336347 will use the LaSalle Bristol ABS Solvent Cement - Black - 1/2 Pint #3447530889. You will simply then just need the length of 3 inch…

view full answer...

Answer 5

Yes, the Galvanized Steel Plumbing Vent, #V2084 will fit PVC pipe with an OD of 1-1/2".

view full answer...

Answer 6

To find the correct replacement flange for your trailer you'll first need to remove your current flange to see exactly how it was attached. Your current flange could be screwed onto the pipe or glued to it so you'll need to find out which…

view full answer...

Answer 7

Since the Valterra Rubber Tank Grommet #F02-2106 is rubber what you would need to use is a hose clamp to tighten and seal the grommet to the piping. You wouldn't need to use any type of sealant. For a hose clamp we have the part #H03-0009 which…

view full answer...

Answer 8

The Valterra Rubber Tank Grommet #F02-2106 can fit a variety of floor or wall thicknesses as it's designed to mount to a toilet floor flange that gets mounted to the floor under the toilet. This grommet does not fit directly to the floor or…

view full answer...

Answer 9

That's a good question but we don't have a way to look that up since Winnebago does not list that as a spec anywhere. You'd have to measure and verify before ordering either the 3 inch #F02-2106 or the larger size #F02-2103. Since the 3…

view full answer...

Answer 10

You will have to cut the flange off if it is glued on and not releasing. Some have luck with a prybar to get it to come loose. Just be careful not to damage anything.

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Fitment of Replacement Rubber Grommet for RV Black Water Tanks, # F02-2106

Product Page this Question was Asked From

Continue Researching