Replacement Mounting Bracket For B&W Turnover Ball Hitch On A 2008 Dodge Ram Pickup

Question

Question:

looking for just the mounting brackets for a turnover ball hitch BandW fitting 2008 2500 Dodge 61/2 bed.

asked by: Moses F

0

Expert Reply:

You will need the B&W Turnoverball Gooseneck Custom Installation Kit for Dodge, part # BWGNRM1308, if you only need the mounting brackets without the center section. If you need the center section as well, the part you need is Center Section for B&W Turnoverball Underbed Gooseneck Hitch - 30,000 lbs, part # BWGNRC907.

I have included product description links below.

expert reply by: Mark Smith

0

Answer 1

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 3

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 5

Yes, it will! The B&W Universal Base Rails and Installation Kit for 5th Wheel Trailer Hitches item #BWRVR3200 includes industry standard 5th wheel rails that are compatible with the Reese 30032 5th wheel hitch. The Reese 30032 uses the same…

view full answer...

Answer 6

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept…

view full answer...

Answer 7

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Answer 8

You will want the hitch to be set at the height that 1) allows the trailer to be level, and 2) allows you a minimum of 6 inches between the bottom of the trailer loft and the top of the bed rails. The fifth wheel hitches offer several inches of up…

view full answer...

Answer 9

Yes, Firestone offers either their Ride-Rite Air Helper Springs #F2299 rated for up to 5,000lbs of capacity or the Ride-Rite Red Label Extreme Duty Air Helper Springs #F2701 rated for a capacity up to 7,500lbs. Do note both of these kits are still…

view full answer...

Answer 10

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the…

view full answer...

Answer 11

I spoke with my contact at Curt regarding the Curt TruTrack Weight Distribution System #C17499 that you are installing on your trailer. He said that you can install the support brackets 6 to 6-1/2 inches from the end of the spring bar without…

view full answer...

Answer 12

Your air bag mounting location will determine compatibility with the Gooseneck trailer hitch #BWGNRK1313. The side plates of the gooseneck trailer hitch #BWGNRK1313 will mount on the outside of each frame rail. See diagram to the right and video…

view full answer...

Replacement Mounting Bracket For B&W Turnover Ball Hitch On A 2008 Dodge Ram Pickup

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching