Where to Mount Spring Bar Support Brackets on Curt TruTrack Weight Distribution System # C17499
Question:
I have purchased and installed a curt c17499 weight distribution system. Due to a battery support being in the way I have the bar supports 3inch from the end of the bars. Will this work or will the bars fall off the supports? My next option is to have the bar supports 6inch to 6 1/2inch from the end of the bars. Will this work? Which option is best?
asked by: Malcolm
Expert Reply:
I spoke with my contact at Curt regarding the Curt TruTrack Weight Distribution System # C17499 that you are installing on your trailer. He said that you can install the support brackets 6 to 6-1/2 inches from the end of the spring bar without issue. This is perfectly fine to do.
The ideal bracket position is 4 to 6 inches in from the spring bar but going a bit over the 6 inches is much better than going below the minimum because as you mentioned, you can start to run into the risk of the bar coming off with the shorter distances.
I have attached the complete installation instructions that you can also use for reference.
Product Page this Question was Asked From
Curt TruTrack Weight Distribution System w/ Sway Control - Trunnion - 8,000 lbs GTW, 800 lbs TW
- Weight Distribution Hitch
- WD With Sway Control
- Some Sway
- Includes Shank
- Electric Brake Compatible
- Surge Brake Compatible
- Fits 2 Inch Hitch
- Allows Backing Up
- 600 lbs
- 700 lbs
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Reese Steadi-Flex Weight Distribution System w/ Sway Control - Trunnion - 10K GTW, 1K TW
- Shop: Curt TruTrack Weight Distribution System w/ Sway Control - Trunnion - 8,000 lbs GTW, 800 lbs TW
- Video: Curt Weight Distribution - WD With Sway Control - C17499 Review
- Shop: Blue Ox SwayPro Weight Distribution w/ Sway Control - Clamp On - 7,500 lbs GTW, 750 lbs TW
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Video: Reese Steadi-Flex Weight Distribution System with Sway Control Review
- Shop: 2-5/16" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long Shank - Raw Finish - 30,000 lbs
- Shop: Blue Ox SwayPro Weight Distribution w/ Sway Control - Clamp On - 7,500 lbs GTW, 750 lbs TW
- Search Results: 40006
- Video: Review of Blue Ox Weight Distribution Hitch - 7.5K WD With Sway Control - BXW0756
- Q&A: Which System Is Best Between The Curt TruTrack & The Equal-i-zer Weight Distribution System?
- Shop: Strait-Line Weight Distribution System w Sway Control - Round Bar - 10,000 lbs GTW, 800 lbs TW
- Search Results: etbc7
- Video: Reese Steadi-Flex Weight Distribution System with Sway Control Test Course
- Video: Reese Strait-Line Weight Distribution System Review
- Video: Reese Strait-Line Weight Distribution System Review RP66082
- Video: Reese Weight Distribution - WD With Sway Control - RP66559 Review
- Q&A: How to Set the Bracket Height on the Curt TruTrack Weight Distribution System Part # C17499
- Q&A: Where to Install the Mounting Brackets of the Curt TruTrack # C17499 Compared to the Hitch Ball
- Q&A: What is Ideal Tongue Weight for Use with Curt Weight Distribution System # C17499
- Shop: Suspension Enhancement
- Q&A: Weight Distribution for 2019 Nissan Pathfinder Towing 2021 Forest River Cherokee Wolf Pup
- Search Results: drawtite activator 3
- Shop: RV Camera
- Q&A: Are Replacement Spring Bars Available For The Curt TruTrack 4P Weight Distribution System # C74RV
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Article: Determining Trailer Tongue Weight
- Article: 5 Tips to Confidently Choose Your Weight Distribution Hitch
Patrick
5/9/2020
Does Curt make an adapter bracket so this can be used on a pole type boat trailer?