How is Control Panel of Lippert Ground Control System Reset

Question

Question:

I bent the rear jacks on my Montana High Country. I got replacement jacks and got them installed. the control panel keeps giving me an error message regarding retract of rear jacks. I did reestablish level using your guidance. How do I get the control panel to reset

asked by: STEPHEN C

0

Expert Reply:

To reset the control panel of a Lippert Ground Control system unplug the control panel # LC421484 for several seconds and then plug it back in. We've seen just doing that alone fix most of the problems with the control panels. If that does not fix the error code let me know.

expert reply by: Jameson C

0

Answer 1

The Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 6-Point Set #LC675817 does require adequate power to work properly. I recommend checking your ground connection from your battery to the trailer frame and…

view full answer...

Answer 2

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point Calibration The…

view full answer...

Answer 3

The "Out of Stroke" error on the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System - 4-Point Set #LC358590 and 6-Point Set #LC675817 means that they have reached the max height, can no longer lift so you need to relocate your…

view full answer...

Answer 4

I have attached for you the installation manual of the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System part #LC675817. This is a generic install manual that can be used on any trailer but there is not a set of instructions specific…

view full answer...

Answer 5

The left front jack error code ("LF) you are getting on your Lippert Ground Control System like #LC675817 can be triggered by a few different things. The first, which it seems you may have already ruled out, is that the system is for whatever…

view full answer...

Answer 6

The good news is your system is working. That lets us rule out 2 of the 3 possible components. Before replacing the third one, I recommend unplugging the connections on the panel and cleaning them prior to reconnecting. If this doesn't solve your…

view full answer...

Answer 7

I spoke with my contact at Lippert and he informed me that the lights flashing indicate the low point of the coach and that if you perform a zero point calibration you will correct that. In the service manual you will need to follow the instructions…

view full answer...

Answer 8

To put your Lippert Ground Control into manual mode it's really just a matter of pressing the manual button on the control panel that's on the top left side of the control panel. Zero Point Calibration The “Zero Point” is the programmed point…

view full answer...

Answer 9

The manually operate any of the jacks on a Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System, like your 6-point part #LC675817, there is a plug on the top and bottom of the motor section. Remove the plug (it doesn't matter if…

view full answer...

Answer 10

If the Lippert Ground Control part #LC675817 display screen is displaying an error that says "Return Leveler for Service" then you should be able to just clear the code. There is not any specific information on why this error code happens…

view full answer...

Answer 11

There are two ways you can manually override the jacks of the Lippert Ground Control kit part #LC358590 that you referenced. You can use a power drill or ratchet to operate them from the top of the leg assemblies or from the bottom. If you check out…

view full answer...

Answer 12

If the touch pad is showing "Retract Time out Return Levelers for service" all you need to do is hit, enter and retract at the same time. That will clear that code. I confirmed this with our contacts at Lippert.

view full answer...