How to Reset Zero Point Calibration on Lippert Ground Control 3.0

Question

Question:

How do you reset the self-leveling I have trouble at all not level out completely

asked by: Chris B

0

Expert Reply:

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 # LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again.

Zero Point Calibration

The “Zero Point” is the programmed point that the trailer will return
to each time the Auto Level feature is used.

Note: Prior to starting this procedure, double check all connections
on the controller, jacks, and touch pad.

1. In manual mode, run the jacks to level the trailer. This is best
achieved by placing a level in the center of the trailer and leveling
it both front to back and then side to side. (See “Basic Jack
Operation” for instructions on how to manually operate the system).
2. Once the trailer is level, turn off the touch pad.
3. With the touch pad off, press and release the “FRONT” button five (5) times and then press and release the “REAR” button five (5) times.
4. The touch pad will flash and beep and the display will read “ZERO
POINT CALIBRATION ENTER to set, Power to Exit”.
5. To set the current position as the zero point, press the “ENTER”
button.
6. LCD display will read “Zero point stability check”.
7. LCD display will read “Zero point set successfully” once process is
complete.
8. The system will set this point as its level state and the touch pad
will turn off.

If this doesn't solve your problem, please let me know and I will continue to help you troubleshoot.

expert reply by: Erik B

0

Bobby

4/25/2024

Did not resolve my problems

Reply

Jerry N.

1/11/2021

I tried the above pushing front then rear 5 times, nothing, then I tried the 10 time method, nothing. I don’t get any sound and the system doesnt turn itself on. Before I started to reset the zero, the system said one of the jacks was out of sink, so 8 manually leveled it. Can u think of why my system doesn’t set to zero?

Reply

Jon G.

1/15/2021

Are you getting a specific error code on your touch pad? If you are manually adjusting the trailer using the jacks and following the steps above but your one of your jacks is still getting messed up then you might need to take your system in to get serviced.

Reply

Rick B.

7/4/2020

I am having trouble with reset procedure it can't work unless all jacks are extended several inches. my problem started when dealer returned unit with dead battery they used system until it failed from low voltage when I try to reset system the first thing it does is try to retract center jacks They are retracted so it aborts procedure. I can't seem to find procedure to lower center jacks manually can you help

Reply

Chris R.

7/8/2020

Try simply clearing whatever error is causing this issue. To do this extend ALL the jacks at least 6", then press and hold the "RETRACT" button until the jacks begin retracting. At this point all the jacks should fully retract and hopefully resolve the issue. Just let me know if not.

Reply

Rick B.

7/8/2020

@ChrisR yes sir you are correct that is exactly what the system tells you to do. however I did not know how extend center jacks to start reset procedure Do you know how to do this?

Reply

Kevin C.

9/24/2020

Turn on the touch pad. Use the up key pad to cycle thru until you teach manual mode and press enter. From here you can extend or lower as needed Once you have it level, then follow the steps Erik posted to set you zero point. Note: on some Lippert systems, you have to press the Front and Rear buttons 10 times versus 5. That’s how mine works.

Reply

See All (4) Replies to Rick B. ∨

Answer 1

We have heard of this issue before on the Lippert Ground Control systems #LC358590. Here is the recommended procedure for clearing the error code: Extend all jacks at least 6 inches. Then press and hold the RETRACT button until the jacks begin…

view full answer...

Answer 2

I reached out to my contact at Lippert and they said that it sounds like you just aren't holding the 4 buttons for the reset long enough. It requires 5 seconds, but many people will count to 5 a little too fast and the system won't…

view full answer...

Answer 3

For your Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System #LC675817 or #LC358590 you need to reset the leveling memory. The “Zero Point” is the programmed point that the trailer will return to each time the Auto Level feature is…

view full answer...

Answer 4

When your Lippert Ground Control 3.0 #LC358590 has a reading that says "Comm Error" it is referring to the communication between the controller and touch pad. You will need to check your harness to ensure it is connected properly…

view full answer...

Answer 5

For the front legs of a Lippert Ground Control 3.0 kit the replacement front jack leg solution you'd need is the part #LC362485. This will allow you to reuse your current motor and bracket. There isn't a gear replacement kit for the…

view full answer...

Answer 6

You have a Lippert Ground Control 6 point kit installed on your RV and the best solution to fix what you have is the part #LC362485. This is the replacement leg portion without the motor for the front of the setup like you are needing. Lippert does…

view full answer...

Answer 7

We do have tire chains that fit 275/65-20 tires for your truck, but unfortunately all of our chains are constructed separately (meaning there is no "crossover" chains that connect the two together for dual wheels). The way the…

view full answer...

Answer 8

On the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w Touchpad and Remote - 4-Point Set #LC358590 the best thing to do to check you level is to recalibrate your system. You do this by resetting your zero point. See the attached…

view full answer...

Answer 9

If you get the Out of Stroke error message on the Lippert Ground Control system, such as #LC358590, then that indicates that the jack has extended as far as it will go and cannot go any further. To clear the error you can extend all of the jacks in…

view full answer...

Answer 10

I spoke with Lippert and unfortunately the model gear you need replaced is not available so you'll need to completely replace the steps. We have multiple options based on the entry height and mounting bracket width you have like the…

view full answer...

Answer 11

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 12

It sounds like you have a Lippert Electric Leveling System like Item #LC358590. The "LF" error message indicates a problem at the left front jack, a ground or short, or perhaps a power issue like the battery stopping to send power.…

view full answer...

How to Reset Zero Point Calibration on Lippert Ground Control 3.0

Product Page this Question was Asked From

Continue Researching