Does The Custom Third Brake Light Camera For Factory 8" Monitor Work With The Sync 3.4 System?

Question

Question:

I have upgraded my 2015 F-350 Super Duty Lariat Crew Cab long bed to the Sync 3.4 system. Will the third brake light camera work with Sync 3.4 the way it does with Sync 2?

asked by: Michael S

0

Expert Reply:

Yes, the Custom Third Brake Light Camera for 8" Factory Monitor # 3460006 will work just fine with the Sync 3.4 system on your 2015 Ford F-350 Super Duty Lariat Crew Cab.

I have also included a video of # 3460006 being installed on a 2015 Ford F-350 Super Duty for you to check out as well.

expert reply by: Bryce D

0

Answer 1

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 2

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 7

Yes the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers part #AL88396 is compatible with the B&W Turnover Ball Gooseneck part #BWGNRK1111. The kit comes with two 3/4" bolts one longer one shorter the longer…

view full answer...

Answer 8

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 9

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 10

Hey John, so the correct amount of spring bar tension will be based on the trailer's tongue weight and how it affects the suspension of your Nissan Frontier. Every WD system is a little different but what it comes down to typically is measuring…

view full answer...

Answer 11

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...