Anti-Sway Bar and Steering Stabilizer for a 1997 Ford F-53 Chassis Motor Home

Question

Question:

I have a 1997 36 foot fleetwood bounder on a ford f53 chassis.this motorhome has a tag axle behind the rear axle.what would be right anti-sway bar for the front and the rear of this motorhome?

asked by: Steve S

0

Expert Reply:

There are several possible options for anti-sway bars and steering stabilizers depending on how your F-53 chassis is configured and what motor is in the RV. I have included a link to the options for you. Use the drop down menu to choose the motor size (V8 or V10) to see the options available.

I have also included a link to our stabilization FAQ article for heavy duty vehicles.

expert reply by: Michael H

0

Answer 1

The Roadmaster Rear Anti-Sway Bar #RM-1139-143 that you referenced is designed to work with a factory sway bar and not replace it. For more information on this sway bar check out the review video and install instructions link I attached.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 9

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is comfortability when you…

view full answer...

Answer 10

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 11

In regards to the Roadmaster Exact Center Steering Stabilizer part #RM47MR, the stabilizer installs on the front of the steering arm pointed down. I have attached a photo of this below. If this wasn't what you were looking for, please just let me…

view full answer...

Answer 12

For your 2024 Ford F-53, I recommend checking out the Timbren Front Suspension Enhancement System #TFFF53B for the front, and the Timbren Rear Suspension Enhancement System #TFRF53A for the rear. These kits do not require drilling, will replace your…

view full answer...