Replacement for Lippert PSX2 Stabilizer Jack 695602

Question

Question:

Do you sell the lippert stabilizer jack part#695602 or just the main arm by itself? I can only find the motor on that part#.

asked by: Chris D

0

Expert Reply:

I do have an option for you but we don't carry the Lippert PSX2 Stabilizer Jack 695602. Instead, we carry the Lippert High-Speed Power Stabilizer Jack part # LC369774 for a white switch, or part # LC298707 for a black switch. These are very similar jacks to what you have now expect they have a single motor design. The footprint and mounting will be the same.

expert reply by: Conner L

0

Answer 1

The SAE codes on the lens of a light indicate what function(s) that light can perform. Many trailer lights are designed to do more than one function. Based on the SAE codes on the first light, it performs the following functions: A - Rear reflector…

view full answer...

Answer 2

The SAE number of a trailer light isn't always the best way to pick out a replacement light since that isn't a part number. But most likely you are looking for a #A32RB which measures 4 inch by 2 inch for red and part #A32AB for…

view full answer...

Answer 3

If your original light is 4" L x 2" W x 1-1/8" D then Optronics light #MC32AB will fit in its place. If you have different dimensions let me know what they are and I can see if we have anything that is a match.

view full answer...

Answer 4

An underslung trailer coupler is one that attaches to the bottom of the trailer frame and an overslung one is one that attaches to the top of the frame. Measuring is not required if you just take a look at your coupler and see where it attaches to…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

For some reason Toyota isn't very forthcoming with how to figure out if you have the tow package or not. From my understanding all of the V6 models of the 2019 Toyota Highlander have the tow package but it isn't specified as to what else…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...