Comparing Dexter Trailer Hub and Drum Assembly 8-219-4UC3-EZ and 8-219-4UC3

Question

Question:

What is the difference between these two hubs?

asked by: Gregory S

0

Expert Reply:

The Dexter Trailer Hub and Drum Assembly # 8-219-4UC3 fits a standard #42 Spindle # TRU57FR. While the Dexter Trailer Hub and Drum Assembly # 8-219-4UC3-EZ fits a E-Z Lube #42 Spindle # TRU37FR. You will need to select the appropriate assembly based on your spindle.

expert reply by: Bud M

0

Answer 1

The reference to 4 leaf springs is the quantity of leaf springs the Tandem-Axle Trailer Hanger Kit, part #AP216-H238. Since it is for a tandem set up you would need to use 4 different leaf springs that are designed for axles up to 8,000 lbs…

view full answer...

Answer 2

Based on the number you listed the correct hub/drum you need is the part #8-219-9UC3 which is a Dexter hub for 5,200-7,000 lb trailer axles that have an 8 on 6-1/2 inch bolt pattern.

view full answer...

Answer 3

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 4

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 5

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 8

Hey Patrick, so for your leaf spring upgrade I am going to need to know a couple of things before I can get you over to the right part. Specifically, the length from eye to eye, the spring width, leaf thickness, and the number of leaves. From here I…

view full answer...

Answer 9

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 10

The hangers you currently have on your trailer are ones I have run into before. That being said, I spoke with MORryde and the #MR27ZR will still fit your trailer, but there is a modification that will need to be made. You’ll have to trim according to…

view full answer...

Answer 11

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Comparing Dexter Trailer Hub and Drum Assembly 8-219-4UC3-EZ and 8-219-4UC3

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching