Does a Curt Trailer Hitch # 14301 Limit Access to the Spare Tire if Installed on 2013 Chevy 1500

Question

Question:

I have 2013 Chevy silverado half ton. Will this not interfere with my spare wheel mounting back in its factory location. my spare wheel is a full size spare wheel.

asked by: Robert S

1

Helpful Expert Reply:

To install the Class IV Curt trailer hitch # 14301 on your 2013 Chevy 1500 you will need to temporarily remove the spare tire for accessibility to the hitch mounting locations. After installation is complete and the spare tire is re-installed you will not have any issues with accessibility or clearance around the full size spare tire when mounted in the factory location.

I have included a photo of this hitch installed on a slightly older Chevy truck, and you can see that there is no interference between the spare tire and mounting location and the Curt Trailer hitch when installed.

To complete your towing package you will also need a ball mount like the # 40331, a pin and clip like # PC3 or a locking option like the # e98882. Depending on the size trailer ball that you will need for towing your trailer either the # A-90 a 2 inch trailer ball or the #19286, which is a 2-5/16 inch trailer ball would be suitable for your towing system.

For a trailer wiring option I recommend the Pollak Custom Fit Vehicle wiring # PK11916. This will provided a 7-pole vehicle connection that can be installed on the bumper of your truck near the license plate. However, if you would like a vehicle connection point that would mount under the bumper of your truck I recommend the Pollak 7-pole Trailer connector # PK11893.

Please note that when towing or using any accessories with your trailer hitch it is not recommended to exceed the lowest rated component of the towing system. Please check your vehicle owners manual or contact the manufacturer and determine the maximum towing capacity of your exact vehicle and make sure that the components that you select for towing are compatible with the capabilities of your 2013 Chevy Truck.

I have included a couple of helpful articles that explains the different components of a towing system, and choosing the correct rise or drop of ball mount. I have also included links to the products recommended and a video demonstrating that product and/or installation of that product. I have tried to provided installation videos on a vehicle similar to yours if available.

expert reply by: Rachael H

1

click to enlarge

Answer 1

Thanks. We think you are pretty awesome, too! You can certainly go to a higher capacity trailer hitch which will help with your current situation and provide additional capacity should you upgrade trailers or boats in the future. Keep in mind…

view full answer...

Answer 2

Part #14301 fits the following vehicles, 2007 New Body Style 1500 Chevrolet Silverado and 2008 1500 Chevrolet Silverado.

view full answer...

Answer 3

I checked the owner's manual for your 2009 Chevrolet Silverado 1500 and the gross combined weight rating (GCWR) of your vehicle is 13,000 lbs. The best way to determine your towing capacity is to load your truck with all the people and cargo that…

view full answer...

Answer 4

The etrailer brand #e98849 is a fit for all trim levels of the 2008 Chevy Silverado 1500, including your LTZ. The hitch has a 6000 lb towing/600 lb tongue weight capacity or 10000 lb towing/1000 tongue weight if used with weight distribution. For a…

view full answer...

Answer 5

The Curt Class IV 2 Inch Hitch, part #14301, will include all of the mounting hardware. I am including a link to the installation instructions of the Curt hitch. If you will be towing with this hitch on your 2007 Chevrolet Silverado New Body you will…

view full answer...

Answer 6

As long as your 2007 GMC Sierra New Body has the standard rear bumper (see photo), I recommend using the Curt Trailer Hitch Receiver part #14301. This is a direct bolt on hitch that will not require any cutting or drilling. You will also be able to…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Does a Curt Trailer Hitch # 14301 Limit Access to the Spare Tire if Installed on 2013 Chevy 1500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching