Vehicles that fit the Curt Class IV Trailer Hitch Receiver

Question

Question:

What types of cars does this hitch, part # 14301 fit?

asked by: Elisa

0

Expert Reply:

Part # 14301 fits the following vehicles, 2007 New Body Style 1500 Chevrolet Silverado and 2008 1500 Chevrolet Silverado.

expert reply by: Amanda

0

Answer 1

The Curt Class IV 2 Inch Hitch #14301 does not bolt to the bumper of your 2008 Chevrolet Silverado. It will bolt to the frame rails of your vehicle. You will need to remove the spare tire to install the hitch, bolt the hitch to the frame rails, and…

view full answer...

Answer 2

Thanks. We think you are pretty awesome, too! You can certainly go to a higher capacity trailer hitch which will help with your current situation and provide additional capacity should you upgrade trailers or boats in the future. Keep in mind though…

view full answer...

Answer 3

To install the Class IV Curt trailer hitch #14301 on your 2013 Chevy 1500 you will need to temporarily remove the spare tire for accessibility to the hitch mounting locations. After installation is complete and the spare tire is re-installed you will…

view full answer...

Answer 4

It's hard to say exactly why the Curt hitch part #14301 doesn't bolt to the bumper like the OEM hitch but most likely they determined that it didn't add much to the strength of the hitch so they left it off. The hitch has been thoroughly…

view full answer...

Answer 5

The factory hitch that came with your GMC Sierra 1500 was at least a Class III and possibly a class IV depending on what trim level you have. Looking at the available products as well as your specific application and towing needs, I recommend…

view full answer...

Answer 6

Of the Curt hitches that you mentioned only the #C15323 is a confirmed fit for your 2003 Chevy Silverado 1500HD. I attached a couple pictures that show exactly how tight this hitch will fit to the rear bumper of the truck as well.

view full answer...

Answer 7

If your truck has a standard or step bumper bumper the Draw-Tite Hitch, part #75362, will fit just fine. If the truck has a 10 inch Deep Drop bumper, you will need to use Curt Hitch part #13339. If you are not sure which bumper you have, I have added…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Vehicles that fit the Curt Class IV Trailer Hitch Receiver

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching