Roof Vent Cover Recommendation for Standard Roof Vent on Rockwood RV

Question

Question:

2018 rockwood 2906ws roof vent cover?

asked by: Donald W

0

Expert Reply:

I recommend checking out the MaxxAir FanMate RV and Trailer Roof Vent Cover # MA00-955002 for your application. This is designed to fit specifically to MaxxFan and MaxxFan Plus roof vents without drilling but it's also compatible with pretty much every other roof vent when using the included mounting hardware.

Attached is a review video for you to check out. If you let me know what brand and model roof vent you have I can see if we have a specific vent cover that fits.

expert reply by: Jon G

0

Answer 1

I have attached for you below the pairing procedure for the Voyager WiSight Wireless RV Backup Camera System part #ASA84YR. Please note, a mistake I have made in the past was applying power to the camera too soon, this cannot be done until the…

view full answer...

Answer 2

Trailer hitch pins and locks do not have an official capacity because they would be rated well beyond what the hitch and vehicle are capable of. In other words, the hitch or vehicle would fail long before the locking hitch pin #e98880 would.

view full answer...

Answer 3

We aren't manufacturers of those parts, and we don't have the testing ability in house, so I reached out to a couple of our manufacturers to see what information they could provide to try and help. I reached out to my contact at Curt…

view full answer...

Answer 4

Duty cycle for a compressor is how long it can run compared to the time needed to cool down. So basically just think of it in increments of an hour - a 33 percent duty cycle over an hour is 20 minutes. And 33 percent at 100 psi is the duty cycle of…

view full answer...

Answer 5

I recommend keeping the Viair Automatic RV Portable Air Compressor #VA59WR in your class A RV motorhome. This compressor will connect directly to your battery with its 12 volt battery clamps. It includes 60' of coiled air hose that will allow you…

view full answer...

Answer 6

The best roof vents we offer for your trailer are going to be the MaxxAir FanMate RV and Trailer Roof Vent Covers part #MA00-955002 for black, part #MA00-955003 for smoke, or part #MA00-955001 for white. The reason for this is because they have the…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...