Recommended Cargo Carrier And Wiring For 2010 Mercedes E350 With Class l Hitch

Question

Question:

Im looking for a cargo carrier that would be compatible with the Class 1 hitch Im installing on my car that has a 1 1/4inch receiver. Suggestions?

asked by: Ross S

1

Helpful Expert Reply:

You will need to check the vehicle owner's manual or with your local dealership and find out what the tongue weight capacity is for your vehicle. Or you can check the safety/warning sticker on the hitch. Please keep in mind the hitch weight limit has to accommodate the weight of the hitch cargo carrier itself added to the weight of the loaded cargo.

You need to also consider the clearance you have when you are attaching any carrier to the hitch of your vehicle. The carrier you referenced is no longer available, but the Reese Hitch Cargo Carrier, part # 63155 is comparable.

The Reese carrier weighs 44 lbs, so for example, if your hitch is rated for 200 lbs tongue weight, then when using this Surco carrier you could load up to 156 lbs of cargo without exceeding the hitch rating.

The pin and clip are sold separately. I would recommend the Pin and Clip, part # PC2 for the carrier. If security is a concern, I would recommend the etrailer # e98880 hitch lock. This allows you to lock your hitch mounted racks or carriers to the receiver on your vehicle, deterring theft.

If you carry cargo that would block the taillights, an optional light kit would be required. I would recommend Cargo Carrier Light Kit, part # 20174. This light kit bolts on easily and plugs into the 4-pole trailer connector of your vehicle.

If your E350 does not have trailer wiring, I would recommend the Curt Powered Taillight Converter with Connector, part # C59236. This kit splices into the taillight wiring of your E-class. To help when installing the wiring kit, I would recommend a circuit tester, like part # PTW2993. I have linked you to a circuit testing video.

expert reply by: Jeffrey L

1

Answer 1

The Curt Powered Converter Wiring Kit #C55152 that you referenced consists of just the wiring that allows you to run wire from a converter to the vehicle's battery. The Curt Powered Tail Light Converter #C59236 you also referenced, which is…

view full answer...

Answer 2

We have two different trailer wiring harness recommendations for a 2011 Mercedes-Benz E350 Wagon. One would be the Curt #C59236 you mentioned, the other would be the #119250KIT from Tekonsha. Both harnesses would need to be wired directly into the…

view full answer...

Answer 3

I reached out to my contact at Curt and was able to confirm that the Curt Trailer Hitch Receiver #C11189 you were looking at is confirmed to fit your 2011 Mercedes-Benz E-350 BlueTech as long as it is a wagon. If your vehicle is a sedan you will need…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 6

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 7

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 8

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 9

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...