What Bolts Are Needed To Mount Thomas Payne Jackknife Hinges To Floor Of 2003 Tiffin Allegro RV.

Question

Question:

I need the bolts to this product that would mount this hinge to the floor.

asked by: James K

0

Expert Reply:

The bolts needed to mount the Replacement Hinge for Thomas Payne RV Jackknife Sofa # 195-000109 to the floor of your 2003 Tiffin Allegro motorhome will depend on where it is being mounted.

If there is not a storage compartment that they are being mounted to you will need the Universal Leg Kit for Thomas Payne RV Jackknife Sofas # 195-000017. If you are mounting these legs in a slide out you will need to use carriage bolts from the bottom of the slide through the floor to hold the jackknife sofa. This will ensure you do not damage the floor under the slide out when moving it in and out of the motorhome. The length of the bolts will depend on the thickness of the floor.

Any bolts needed would need to be sourced from a local hardware store to ensure you have the correct length needed.

expert reply by: Bud M

0

Answer 1

The Replacement Hinge for Thomas Payne RV Jackknife Sofa #195-000109 (Right Hand) and #195-000108 (Left Hand) both measure 19-3/4 inches in length. I have added links to video reviews of both parts for you to check out.

view full answer...

Answer 2

The closet thing we have to what you are describing is the Universal Leg Kit for Thomas Payne RV Jackknife Sofas item #195-000017. These are designed for RVs that don't have a pre-existing platform or frame but they would provide your tri-fold…

view full answer...

Answer 3

The only brackets that we have for a Thomas Payne Jackknife sofa come in the Universal Leg Kit #195-000017 and are used for mounting them to the floor. If you are needing to mount the sofa directly to the wall then you'll need to source those…

view full answer...

Answer 4

There are holes in the jackknife leg kits like part #195-000017 that are designed to allow you to run hardware through them and also through the floor of your RV. There isn't a set of install instructions I can point you towards as every…

view full answer...

Answer 5

We have a great option in a replacement 45 amp power converter for your ELX-45. I suggest the Progressive Dynamics, #PD4045KA. This is a 2-in-1 AC/DC distribution panel and smart charger that works with lithium-ion, flooded lead acid, AGM, and gel…

view full answer...

Answer 6

Thanks for the photo, and I searched but could not find anything with the numbers on the sticker. Truly, the only way to know which is the correct replacement is to know the model of your Lippert stabilizer jack. There are only a couple that are…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The 8-14.5 tires are an older metric size no longer used today. Therefore, you would need to replace these along with the wheels in order to update them. In order to see if we have any options for you, we'd first need to determine the bolt…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...