What Camper Tie-Downs do You Recommend for My 2016 Ram 2500 with Running Boards and Hitch?

Question

Question:

It’s a short bed and a crew cab non-dually. They are aftermarket running boards. And there is a receiver hitch that is not a Torklift model.

asked by: George S

0

Expert Reply:

Thanks so much for reaching out to us for camper tie-downs. In order to determine the correct fit, can you confirm your bed length and cab style for me? Also, with your running boards, are they factory or aftermarket? Lastly, do you have a hitch installed on your truck?

expert reply by: Bob C

0

George S.

1/1/0001

It’s a short bed and a crew cab non-dually. They are aftermarket running boards. And there is a receiver hitch that is not a Torklift model.

Reply

Bob C.

2/21/2022

I have a great solution for you. While we do not carry just the rear tie-downs sold individually, we do have complete kits. Without knowing specifically the exact dimensions and model of your aftermarket running boards on your 2016 Ram 2500 crew cab, the best option is the HappiJac Truck-Mounted Camper Tie-Downs # LC236326-205221. The HappiJack tie-downs include front tie-down brackets attach to your truck bed's frame allowing the tie-downs to become integral parts of your truck. Also, when you're not hauling your camper, you don't have to worry about bulky brackets sticking out of your truck, creating an eyesore or hazard. This 100% U.S.A.-made kit comes wit all hardware required for installation. If you need turnbuckles, I recommend the HappiJac Original Turnbuckles for Camper Tie-Downs # LC182898.

Reply

Answer 1

Congratulations on your new truck bed camper! I'm sure you will enjoy it for many years. Sway is a common issue with truck bed campers which can be reduced, but not eliminated. The campers are not particularly aerodynamic and the sway will…

view full answer...

Answer 2

You can definitely install the HappiJac tie-downs in the front and use Torklift tie-downs for the rear, but you'll have to purchase the whole Happijac kit #LC236326-205221 since we don't currently offer the front separately. For the rear…

view full answer...

Answer 3

On the etrailer website, the Roadmaster Rear Anti-Sway Bar is listed as #RM73FR and yes this is the Roadmaster 1129-145. Anything listed on this site as having a confirmed fit means it has either been installed by an etrailer Tech on site or we have…

view full answer...

Answer 4

The 2 new backing plates on the HappiJack Tie-Downs #LC236326-205221 were added to provide an additional set of mounting screws and give the behind bed brackets some additional stability.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 10

Hey Ted, so if you look in the bed of your truck and see 5 holes/pucks that would mean you have the OEM prep. I'd assume if you had it you'd have seen them by now. If you had it you'd only need a ball like the part #C60618. If you…

view full answer...

Answer 11

The support braces in the HappiJac Truck-Mounted Camper Tie-Downs #LC182860 are going to attach to the cross frame to provide support for the anchors which will bolt through the bed wall and into the braces. The rear anchors will bolt through the…

view full answer...

Answer 12

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...