Replacement Coupler Solution for Shelby 5135

Question

Question:

Do you sell the part the ball Locking mechanism broke on mine Or do I have to buy the hole assembly

asked by: Scott K

0

Expert Reply:

Since Shelby couplers aren't available you would need to buy an all new coupler like with the part # CT-5003-Z that you mentioned. This fits 3 inch channel like what you have and also is designed for the same 2 inch hitch ball size.

expert reply by: Jameson C

0

Answer 1

I recommend etrailer.com Channel Tongue Coupler part #CT-5003-Z to replace the Shelby 5135 coupler. The etrailer.com coupler has a channel width of 3" and takes a 2" ball. It also has 3" from center of bolt hole to center of bolt hole…

view full answer...

Answer 2

To mount the Channel Tongue Trailer Coupler - Trigger Latch - Bolt On #CT-5003-Z, I recommend using 1/2 inch bolts. The higher the grade, the stronger the bolt. I've attached the review video to help as you plan this installation.

view full answer...

Answer 3

The mounting holes of the etrailer.com trailer coupler are spaced 3-1/16 inches apart on center. The holes themselves are a 1/2 inch in diameter.

view full answer...

Answer 4

I recommend etrailer.com Channel Tongue Coupler part #CT-5003-Z to replace the Shelby 5135 coupler. The etrailer.com coupler has a channel width of 3" and takes a 2" ball. It also has 3" from center of bolt hole to center of bolt hole…

view full answer...

Answer 5

The only difference in the Demco Channel Tongue Trailer Couplers #DM16080-95 and #DM15931-95 is going to be the bolt pattern. One will have the 5-Bolt hole pattern and the other is going to have 4-Bolt holes. I have included images below showing the…

view full answer...

Answer 6

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 7

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 8

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 9

Thank you for the image. It appears you will need either the Demco Channel Tongue Trailer Coupler #DM13203-95 or #DM16080-95. Both of these couplers have a zinc coating for increased corrosion resistance and fit on a standard 3" wide channel…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

You're correct. The repalcement for your existing B12EA-22 brake would be #AKEBRK-7R-SA for the right side and #AKEBRK-7L-SA for the left.

view full answer...

Answer 12

You can certainly go ahead and re use the existing 2 bolts, provided they are in good condition. The fish wire method shown in the video works too, but it is also very common to just use the two bolts like your old Atwood actuator. Personally I would…

view full answer...

Replacement Coupler Solution for Shelby 5135

Product Page this Question was Asked From

Continue Researching