Weight Of The TorkLift # TLT2303 And # TLT3303 Camper Tie-Downs

Question

Question:

How much do each of these products weigh? TorkLift TLT2303 front and TLT3303 rear camper tie-downs - weights

asked by: John D

0

Expert Reply:

The TorkLift Custom Frame-Mounted Camper Tie-Downs - Front # TLT2303 weighs approximately 17lbs and the TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear # TLT3303 weighs approximately 19lbs.

expert reply by: Kevin C

0

Answer 1

I spoke with TorkLift about the TorkLift Custom Frame-Mounted Camper Tie-Downs for a 2018 Toyota Tacoma and they stated they have not done any testing on the TRD. That said, it looks like the only issue would be the factory nerf bars so if these are…

view full answer...

Answer 2

There is no drilling required on your 2017 Toyota Tacoma to install the TorkLift Custom Frame-Mounted Camper Tie-Downs - Front #TLT2303. I have added the installation instructions for you to look at, which include the necessary steps needed for…

view full answer...

Answer 3

For 4WD models you'll need to use the TorkLift Custom Frame-Mounted Camper Tie-Downs #TLT2303 for the front and #TLT3303 for the rear. If you have a 5' bed and running boards under the cab will need to remove the running boards to install tie…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 6

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 7

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 8

Hey Robert, sorry it can be a bit confusing navigating all those facets for the camper tie downs, but I did go ahead and find those tie downs you were looking for. For the front, you'll want the TorkLift Camper Tie-Downs #TL87CR (TorkLift P/N…

view full answer...

Answer 9

You can definitely install the HappiJac tie-downs in the front and use Torklift tie-downs for the rear, but you'll have to purchase the whole Happijac kit #LC236326-205221 since we don't currently offer the front separately. For the rear…

view full answer...

Answer 10

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 11

The current Torklift tie down part #TLD3101 that you have installed on your 1997 Dodge Ram 3500 only fits if you have the factory hitch. If you go with the SuperHitch part #TLD1100 you would need to change your rear tie down to the part #TLR3503.

view full answer...

Answer 12

The F2032 you're looking for is under part #TL87CR on our website and would be the correct fit for your 2024 Ford F-350. For the rear tie-downs you'll need part #TLF3008. To complete the setup you can use the TorkLift AnchorGuard Derringer…

view full answer...

Weight Of The TorkLift # TLT2303 And # TLT3303 Camper Tie-Downs

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching