Will the TorkLift Custom Frame-Mounted Camper Tie-Downs Fit a 2018 Toyota Tacoma TRD

Question

Question:

Does this fit a 2018 Toyota Tacoma TRD Off Road 6 foot bed?

asked by: Sean

0

Expert Reply:

I spoke with TorkLift about the TorkLift Custom Frame-Mounted Camper Tie-Downs for a 2018 Toyota Tacoma and they stated they have not done any testing on the TRD. That said, it looks like the only issue would be the factory nerf bars so if these are equipped they would need to be removed. Otherwise, I don't see any issues with the TorkLift Custom Frame-Mounted Camper Tie-Downs on a Toyota Tacoma TRD.

The correct TorkLift Custom Frame-Mounted Camper Tie-Downs for a 2018 Toyota Tacoma 4x4 with 6' bed is part # TLT2303 for the front and part # TLT3307 for the rear. If you don't already have tie-downs, the TorkLift Locking FastGun Turnbuckles part # TLS9522-2-LK are what I recommend as they are locking and made of stainless-steel so they will not rust or corrode.

expert reply by: Conner L

0

Answer 1

There is no drilling required on your 2017 Toyota Tacoma to install the TorkLift Custom Frame-Mounted Camper Tie-Downs - Front #TLT2303. I have added the installation instructions for you to look at, which include the necessary steps needed for…

view full answer...

Answer 2

The TorkLift Custom Frame-Mounted Camper Tie-Downs - Front #TLT2303 weighs approximately 17lbs and the TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear #TLT3303 weighs approximately 19lbs.

view full answer...

Answer 3

For 4WD models you'll need to use the TorkLift Custom Frame-Mounted Camper Tie-Downs #TLT2303 for the front and #TLT3303 for the rear. If you have a 5' bed and running boards under the cab will need to remove the running boards to install tie…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 9

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 10

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Will the TorkLift Custom Frame-Mounted Camper Tie-Downs Fit a 2018 Toyota Tacoma TRD

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching