Bearing Kit For Kodiak Trailer Hub KH84545S

Question

Question:

What bearing kit would be compatible with this hub KH84545S. Also do any bearing kits come in stainless steel? Thank you.

asked by: Greg

0

Expert Reply:

We do have the right bearing kit for your Kodiak Trailer Hub for 3,500 lb Axles # KH84545S, and though they are steel, they aren't stainless steel. The correct bearing kit for your hub is the following:

- Hub Bearing Kit # BK2-100

Along with the # BK2-100, if you need a bearing packer and grease, go with the Bearing Packer # PTW1218 and LubriMatic LMX Grease # L11390.

expert reply by: Kyle S

0

Answer 1

Let's start with the brake assemblies, which you were kind enough to give the dimensions on for the drum, as well as the axle capacity, which are the most important things. For self-adjusting electric brakes I recommend the Electric Trailer Brake…

view full answer...

Answer 2

Since trailer manufacturers used many different components, we have no idea what was used on a trailer. The best way to find the right components is to pull the bearings and get the numbers off the bearings that may be stamped or etched. If you…

view full answer...

Answer 3

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 4

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 5

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 9

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 10

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 11

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Bearing Kit For Kodiak Trailer Hub KH84545S

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching