Curt or Draw Tite Trailer Hitch for 2013 Scion FR-S

Question

Question:

Which trailer hitch is better between the curt trailer hitch and the draw tite trailer hitch for a Scion FR-S !

asked by: Jose T

0

Expert Reply:

For your 2013 Scion FR-S I would recommend the Draw Tite part # 24935 over the Curt hitch # C11379 as only the hitch opening hangs below the rear bumper which gives you a more hidden look while also helping with ground clearance.

expert reply by: Jameson C

0

Answer 1

Since the Curt Trailer Hitch Receiver #C11379 does require Stabilizing Straps #18050 you will want to use the Draw-Tite Sportframe Trailer Hitch Receiver #24935. This is a class I receiver that will give you a 1-1/4 in receiver on your 2013 Subaru…

view full answer...

Answer 2

When you are having the problems on your 2013 Scion FR-S do you have anything plugged into the Curt wiring harness #C56212? If nothing is plugged into the 4-Way then it should not be drawing any power from the vehicle tail light connections. The…

view full answer...

Answer 3

The Curt hitch part #C11379 that you referenced has been confirmed as a fit for your 2015 Subaru BRZ so it would work well for you. I looked up pictures of your vehicle and the trunk looks like it opens basically straight up so it would not interfere…

view full answer...

Answer 4

The Draw-Tite Sportframe Trailer Hitch Receiver part #24935 does install between the the bumper cover and the bumper so the rear fascia does not need to be removed because it is a concealed cross tube hitch. The only part of the hitch that is visible…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Curt or Draw Tite Trailer Hitch for 2013 Scion FR-S

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching