Does Rear Panel Need To Be Removed To Install Draw-Tite Hitch 24935 On 2019 Subaru BRZ

Question

Question:

when I install the draw-tite on my 2019 Subaru BRZ do i need to remove the rear fascia

asked by: maria

0

Expert Reply:

The Draw-Tite Sportframe Trailer Hitch Receiver part # 24935 does install between the the bumper cover and the bumper so the rear fascia does not need to be removed because it is a concealed cross tube hitch. The only part of the hitch that is visible once installed is the receiver. The bumper cover will be replaced after the hitch is installed. I have attached a snip from the installation instructions that explains this step.

expert reply by: Heather A

0

click to enlarge

Answer 1

Since the Curt Trailer Hitch Receiver #C11379 does require Stabilizing Straps #18050 you will want to use the Draw-Tite Sportframe Trailer Hitch Receiver #24935. This is a class I receiver that will give you a 1-1/4 in receiver on your 2013 Subaru…

view full answer...

Answer 2

For your 2013 Scion FR-S I would recommend the Draw Tite part #24935 over the Curt hitch #C11379 as only the hitch opening hangs below the rear bumper which gives you a more hidden look while also helping with ground clearance.

view full answer...

Answer 3

The Curt hitch part #C11379 that you referenced has been confirmed as a fit for your 2015 Subaru BRZ so it would work well for you. I looked up pictures of your vehicle and the trunk looks like it opens basically straight up so it would not interfere…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Does Rear Panel Need To Be Removed To Install Draw-Tite Hitch 24935 On 2019 Subaru BRZ

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching