Correct Wedge For PullRite SuperGlide Hitch

Question

Question:

Will this wedge sww-003 work with a Pullrite Superglide hitch?

asked by: Ryan D

0

Expert Reply:

The 5th Airborne Custom Wedge # SWW-03 is designed for select Draw-Tite hitches and is meant to work with the Sidewinder and 5th Airborne Sidewinder. Instead, the MORryde Orbital Pin Box Wedge for PullRite SuperGlide Hitch # MR65TR will work with MORryde pin boxes, and is intended to work with the PullRite SuperGlide you mention.

Also, the Sidewinder Wedge Kit for Pullrite and Camco Fifth Wheel Trailer Hitches # RP99FR will also work with sidewinders/turning points.

expert reply by: Bryce D

0

Answer 1

Yes, the Reese wedge part #RP99FR is the correct wedge to use with ta Lippert Turning Point pin box and a Pullrite ISR fifth wheel hitch.

view full answer...

Answer 2

The Curt X5 Fifth Wheel Adapter for B and W Square Shank Turnover Ball Hitches, #16310, is designed for use with B and W square shank turnover ball hitches. We spoke with Curt and they stated the Pullrite 5th wheel hitch is not compatible with the…

view full answer...

Answer 3

I spoke with my contact at Valley and the Valley Gooseneck-to-Fifth-Wheel Adapter Plate, #V70881, will not work with the Curt slider rails. Instead, I would recommend using the Curt X5 Adapter Plate, #16310. This adapter plate will work with your…

view full answer...

Answer 4

The Demco #DM6140 will work with your B&W 1307 Turnoverball gooseneck hitch as is. The B&W gooseneck hitch uses a square hole for the ball, so you will just remove the ball, and the Demco #DM6140 will go directly into the square hole.…

view full answer...

Answer 5

Let's start with the adapter you need for the Curt EZr Double Lock Underbed Gooseneck Trailer Hitch #C611-624 in your 2019 GMC Sierra 2500 short bed, which is the Curt X5 5th-Wheel Base Rail Adapter Plate for EZr Double Lock Gooseneck…

view full answer...

Answer 6

Easiest way to tell which gooseneck hitch you have is by looking at the safety cable loops. If they are about as wide as the gooseneck ball hole and are centered with the ball hole it's an EZr, if the safety chain loops are a smaller and…

view full answer...

Answer 7

If your Pull Rite hitch is the ISR (industry standard rail compatible hitch), then yes the Curt X5 #16310 that you referenced would work well with your hitch. The mounting slots for the tabs on the 5th wheel measure 22 inches front to back on…

view full answer...

Answer 8

The difference between manual and automatic sliding 5th wheel hitches is that with a manual sliding hitch you simply move the hitch body forward or backwards before maneuvering to give yourself more clearance. Automatic sliders use a rotating head…

view full answer...

Answer 9

Using Loctite when installing a trailer hitch is not required but it can certainly be used to create an even stronger bond. Blue Loctite like the Blue Stick #LT37643 is plenty sufficient for this application. As long as the hardware for your hitch…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from…

view full answer...