Availability of Convert-A-Ball Cushioned Ball Mount with 2 Inch Drop

Question

Question:

Please refer to your product AMSC6. Do you have a similar cushioned ball mount with a 2 inch drop , instead of the 6 inch drop of this product? Thanks

asked by: Phillip S

0

Expert Reply:

We do indeed offer a Convert-A-Ball cushioned ball mount with a 2 inch drop. We offer it as part # AMSC2.

If you click the provided link, you can see a demonstration video featuring the # AMSC2 ball mount.

expert reply by: Mike L

0

Answer 1

From the base of the #C40047 up to the top of the ball measures 4.091 inches. This is about 1-3/8 inches taller than a standard ball.

view full answer...

Answer 2

We don't have a combo of the Curt Hitch Ball #C40008 and Curt Ball Mount #C45340. The ball mount is extremely heavy-duty, rated up to 17,000 pounds. I think it's safe to assume you don't have a torque wrench rated up to 450 foot pounds…

view full answer...

Answer 3

In order to pick out the correct height ball mount you need to take two measurements and make one easy calculation. Check out the FAQ article I attached that details how this is done. Basically you will measure the height of the hitch on your 2011…

view full answer...

Answer 4

Yes, there is another option to add a brake controller to your Ranger. Since you have the factory tow package, I recommend the Curt Echo In-Line Wireless Brake Controller item #C79DR. The controller plugs in behind your 7-way with included…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 11

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 12

The ideal height will actually have to do with how tall the coupler of the trailer is from the ground. The Draw-Tite #76020 will sit at 13 1/2 inches from the ground to the top of the hitch when installed on a 2016 Mazda CX-9. From what I could find…

view full answer...

Availability of Convert-A-Ball Cushioned Ball Mount with 2 Inch Drop

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching