Replacement Keyed Alike Slam Latches Needed

Question

Question:

I need 11 replacement locks. The opening is 1inch thick and measures 3.5inch wide x 3.75inch height. I need to replace a Fastec Industrial model and would need all keyed alike. Do you have a replacement for this opening?

asked by: Edward S

0

Expert Reply:

I am not seeing where we have an exact replacement but please look at the Global Link Locking Baggage Lock Actuator Set with Mounting Plate, # GL34FR. This will require a cutout of approximately 3-3/4" x 3-3/4". These will all be keyed alike to a G391.

expert reply by: Michael R

0

Answer 1

I checked the NADA Guide for details on your travel trailer model RBC26. The nearest model number designation I found was the Gulf Stream Ultra Lite Series 29-foot travel trailer model M-26CRB. I reviewed this item on the Gulf Stream website but no…

view full answer...

Answer 2

Yes. If you were to order 4 of #295-000077 and selected the "keyed alike" option all of the locks would be the same. The default is "keyed unique" so be sure to change it before selecting the add to cart button.

view full answer...

Answer 3

Best option would be to use a rubber grommet that fits the hole that the cam lock fit into after installing the Global Link Locking Baggage Lock Actuator Set with Mounting Plate #GL34FR. You'll need to measure the diameter of the hole after…

view full answer...

Answer 4

The Global Link Locking Baggage Lock Actuator Set with Mounting Plate part #GL34FR comes with a specific key and lock, coded as 391. Therefore, if you order multiple they will all come with this same key but you don't need to do so all at one…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 11

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 12

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...