Replacement Trailer Axle For a 10 X 6 Aluma Utility Trailer That Has A Torsion Axle

Question

Question:

I have a aluma utility trailer 10 feet long x 6 feet wide Aluminum deck I need a torsion axle for it It is 72 inch axle or 6 feet 7 3/4 inch between mounting holes Standard 5 hole hubs Can you help me

asked by: James S

0

Expert Reply:

I have a product that may work for you as we do not carry any torsion trailer axles like the one under your 10'X6' Aluma utility trailer.

The Timbren Axle-Less Trailer Suspension System # A20RS545 is rated for 2,000lbs and will mount to the frame rails on your Aluma utility trailer. This kit includes the idler hubs that fit a 5 on 4-1/2" lug pattern wheel.

If you have the heavy duty Aluma utility trailer it will have a 3,500lb torsion axle and the Timbren Axle-Less Trailer Suspension System # A35RS545 would be the one that you want to use. This has the same 3,500lb capacity of your torsion axle and this system also includes the 5 on 4-1/2" hub pattern idler hubs.

expert reply by: Bud M

0

Answer 1

It is a very good idea to keep spare bearings and seals (and wheel bearing grease too) on hand for the unexpected roadside stop. We have individual bearing and seal parts like #L68149, #L44649 and #58846 as well as kits like #BK2-100 that combine…

view full answer...

Answer 2

It is possible to weld on a brake flange such as Brake Mounting Flange for 1-3/4" Round Trailer Axles - 2K #4-34 for 1-3/4" round axles, but it takes a qualified welder and even then it can be difficult to accomplish. A better…

view full answer...

Answer 3

The 4 hole brake mounting flange will work for 10 inch brakes because the 7 inch and 10 inch assemblies use the same 2-7/8 inch on center mounting holes. The brake assemblies like #AKEBRK-35 or self-adjusting assemblies like #AKEBRK-35-SA will both…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 7

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...