Correct Replacement Castle Nut, Cotter Pin, and Washer for Trailer with 1" Round Spindle
Question:
I had asked a question the other day, I dont think I gave enough detail. While traveling with my boat on I noticed an issue with my trailer wheel and immediately pulled over. Bearing Buddy and castle nut were gone and I am lucky I did not lose the tire. The axle spindle looks to be okay, will need to rethread it as it has some damage attached. I am not sure if that is advisable or not, but considering this is most likely a custom sized axle I would prefer to repair. 15902-COTTER PIN SPINDLE 15903-WASHER 1.06 SPINDLE 15910-NUT SPINDLE Can you help with cross referencing the parts listed?
asked by: Robert J
Expert Reply:
The correct replacement castle nut, cotter pin, and washer for a trailer with 1" round spindle is as follows: Castle Nut part # 165686, Cotter Pin part # 165649, and Washer part # SW1000.
Unfortunately, we can't cross-reference trailer mfg. part numbers but the above parts are fairly standardized so there will be no issues with compatibility.
Products Referenced in This Question
Cotter Pin - 1/8" Thick x 1-3/4" Long
- Accessories and Parts
- Trailer Suspension Parts
- Cotter Pin
- ABS Fasteners
more information >
Product Page this Question was Asked From
Continue Researching
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 4-1/2 - Galvanized
- Shop: Replacement Center Cap for Taskmaster Viking Aluminum Trailer Wheels - 3.19" Pilot - Qty 1
- Shop: Lionshead Trailer Wheel Lug Nut - 1/2"-20 - Stainless Steel - Qty 1
- Video: etrailer Trailer Idler Hub Assembly Review AKIHUB-440-2-1K
- Shop: Cotter Pin - 1/8" Thick x 1-3/4" Long
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Trailer Spindle Nut 1"
- Shop: Washer For 1" Spindle
- Search Results: wheel lug nut
- Search Results: center caps
- Video: Review of etrailer Trailer Hubs and Drums - Hub - AKIHUB-440-2-2K
- Video: etrailer Trigger Latch Channel Tongue Trailer Coupler Review
- Q&A: How To Tell If Bearing Buddy Has Enough Grease
- Search Results: castle nut
- Q&A: My Axle Has No Cotter Pin Hole Can I Install Bearing Kit for #84 Spindle?
- Q&A: How to Determine if the Grease Cap for a Hub
- Q&A: Can Hub That Had Bearing Buddy Installed Be Used on Axle With EZ Lube Spindle
- Q&A: Should There Be a Washer Between Outer Bearing and Castle Nut on etrailer 2,000 lb Trailer Axle
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Q&A: Spindle Nut Recommendation for 84 Spindle
- Search Results: ez lube hubs
- Search Results: hubs
- Search Results: ball
- Search Results: coupler
- Q&A: How to Easily Determine Trailer Wheel Bolt Pattern
- Video: Review of etrailer Trailer Hubs and Drums - Hub - AKIHUB-440-2-1K
- Video: etrailer Trailer Hubs and Drums - Hub - AKIHUB-440-2-G-1K Review
- Article: Trailer Jacks
- Article: Trailer Wiring Diagrams
- Article: 5 Tell-Tale Signs It’s Time to Replace Your Trailer’s Leaf Springs
on Accessories and Parts
