Recommended Rear Suspension Enhancement for a 2020 Ram 1500 Rebel

Question

Question:

I have a 2020 Ram 1500 Rebel 4x4 eco diesel. Towing 31ft TT with roughly 750lbs tongue weight and 7500lb dry weight. Adjustable hitch has my TT level but truck squats a little more than I want. Thinking Timbren would give me enough support when hauling and when I’m running empty I wouldn’t even know they’re on. Thoughts if this is a good choice as I’m not an airbag fan.

asked by: Dar M

0

Expert Reply:

The Timbren Rear Suspension Enhancement System # TDRTT1500 will definitely give you good support when towing, but they will also affect your ride when not towing due to how much stiffer they are than the stock jounces. This is why I usually recommend an air bag system, like the Air Lift LoadLifter 5000 # AL57375 as they are completely adjustable. However, if you are not preferable to air bags, the Timbren # TDRTT1500 will be the most heavy duty option we have for your truck.

expert reply by: Lazer S

0

Answer 1

No, use of the Timbren suspension enhancements like the Timbren Rear Suspension Enhancement System #TDRTT1500 will not void your warranty. You are protected by the Federal Magnuson-Moss Warranty Act. This act says if something breaks on your vehicle…

view full answer...

Answer 2

I looked up some photos of the 2022 Ram 1500 Rebel side mirror and they appear to match the other models so the Longview Custom Towing Mirrors part #LO34FR should be an exact fit option for you. I have attached an install video I did of these on a…

view full answer...

Answer 3

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 4

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Recommended Rear Suspension Enhancement for a 2020 Ram 1500 Rebel

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching