Width of Hydraulic Brake Kit AKFBBRK-35-D

Question

Question:

Do you have the dimensions of this kit? the largest outside diameter of the drum.

asked by: Todd L

0

Expert Reply:

The width is 2-1/4" for the Hydraulic Brake Kit - Uni-Servo - Free Backing - Dacromet - 10" - Left/Right Hand - 3,500 lbs # AKFBBRK-35-D, so you will need hub and drums that are at least that wide for these to fit; though that width (or more) is standard for 3,500 lb, 10" hub and drum assemblies.

To mount the Hydraulic Brake Kit # AKFBBRK-35-D you will also need the Mounting Hardware for 10" Brake Assemblies # BRKH10B.

If you need a hub and drum as well, I've added a link below to our 3,500 lb options.

expert reply by: Kyle S

0

Answer 1

The #84 E-Z Lube Spindle with Brake Flange for 3,500-lb Trailer Axles #TRU77FR has a brake flange with the standard bolt hole spacing of 2-7/8 inches apart on center. There isn't a flange available with 2-3/8 inch by 2-1/2 inch spacing, but we do…

view full answer...

Answer 2

We do have the correct hub & drum with bearings for your 2016 Starcraft AR-ONE 18QB travel trailer with a 3,500 lb axle. The correct part is the Trailer Hub and Drum Assembly - 3.5K E-Z Lube Axles #AKHD-545-35-EZ-K. This comes pre-greased with…

view full answer...

Answer 3

The only option for an axle for your M416 trailer is what is called an axle-less system, as there aren't axles in that particular length. You can get these with either idler hubs (for without electric brakes) or hub and drums if you choose to use…

view full answer...

Answer 4

Outstanding information, thanks so much, and what you have, based on those measurements are a spindle for a 3,500 lb axle, with outer bearing L44649 and inner bearing L68149. For that, what you need is the following hub and drum: - Trailer Hub and…

view full answer...

Answer 5

Let's start with the brake shoes, and there are replacement brake shoes for the Dexter 10" x 2-1/4" electric brakes, but they do need to be the Dexter Nev-R-Adjust, self-adjusting brakes. If you have those, what you need are these…

view full answer...

Answer 6

Yes, you are absolutely correct; the self-adjusting electric trailer brakes for your Dexter 3,500 lb axles are indeed the part number you referenced: - Electric Trailer Brake Kit - Self-Adjusting - 10" - Left and Right Hand Assemblies - 3,500…

view full answer...

Answer 7

I had the bolt holes on the TruRyde #84 E-Z Lube Spindle w/ Brake Flange for 3,500-lb Trailer Axles #TRU77FR measured, and they are .488", or just under 1/2". This size corresponds with the bolts that typically come pre-installed on…

view full answer...

Answer 8

I went ahead and called my contact at Redline Trailer Repair Parts, and they confirmed that nuts in the Mounting Hardware for 10" Brake Assemblies #BRKH10B have a diameter of 7/16mm and have 20 threads per inch. Unfortunately, there are no bolts…

view full answer...

Answer 9

There is one hub and drum that will fit the Timbren Axle-Less Trailer Suspension System - Spindle w/Brake Flange - Off-Road Tires - 2,200 lbs #ASR1THDS02. The correct part is the Dexter Trailer Hub and Drum Assembly #84546UC3-EZ. The #DX68XR says it…

view full answer...

Answer 10

The #TRU77FR spindle accepts a 3 inch axle beam, and the spindle is designed to be welded into place. If the axle tube is painted on the ends, you'll want to take the tubing down to bare metal so you get the proper penetration on your weld.

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...