Looking For CoverBra For Bearing Buddy

Question

Question:

I have Bearing Buddies that measure exactly 2. I can not find a model number on them. What model/size coverBra would I need and where do I get them?

asked by: Mike G

0

Expert Reply:

It sounds like you are looking for the Bearing Buddy coverbra # BB19B. The closest Bearing Buddy sizes that are close to the 2 inches that you measured are either 1.98 inches or 2.047 inches.

The Bearing Buddy # BB17B you referenced are too small for your bearing, the largest they hold is 1.81 inches.

To get an accurate measurement to find the correct coverbra, measure the inside diameter of the Bearing Buddy where the hub sits with a caliper.

expert reply by: Lori W

0

Answer 1

If you have model 1781, or 1781SS, the correct replacement Bearing Buddy Bra will be #BB17B. These covers are going to slide over your Bearing Buddy, and have an outer diameter of two inches.

view full answer...

Answer 2

The Replacement Bearing Buddy Bras Model 17B, part #BB17B, will fit on Bearing Buddy grease caps for hub bores from 1.781-inches to 1.810-inches. These caps will have an outer diameter of close to 2-inches. Because these bras are made of flexible…

view full answer...

Answer 3

There should be a label or a plate on the axle or on your trailer that should have the weight capacity listed. Since there can be many combinations of axles with hubs and bolt patterns, the best way to determine your axle weight capacity and which…

view full answer...

Answer 4

I went and pulled the Replacement Bearing Buddy Bras #BB19B from our warehouse to get the dimensions you requested and found them to be 2.07 inches from the inside of the cover and 1.29 inches deep.

view full answer...

Answer 5

Since you said the outer diameter of the Bearing Buddy you have now is 2-1/8 inch the correct replacement bra for it is the part #BB19B.

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

A tow package for a vehicle is usually a frame mounted trailer hitch and trailer wiring on a vehicle like your 2002 Dodge Dakota. If you have those two things you could pretty easily assume you have the tow package. Or, you can take the VIN of your…

view full answer...

Answer 9

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Answer 10

The best modern day size replacement option we have for a 6.00-16 is a 235/80-16 which measures 30-7/8" diameter x 9-3/8" wide. For this, I recommend the Kenda Karrier ST235/80R16 Radial Trailer Tire with 16" Black Mod Wheel part…

view full answer...

Answer 11

The Solera Gas Strut part #LC280343 is designed for Lippert-Solera branded awnings. That said, it should be able to be used with others but you'd need to verify the dimensions in order to ensure compatibility. The length for this strut will be…

view full answer...

Answer 12

There is a Titan hitch extender that should work for you, but would require a Titan hitch be installed on your truck to handle a tongue weight loaded that far from the hitch. It is Reese part #RP45292. You can use it as a 34 inch extension or cut it…

view full answer...

Looking For CoverBra For Bearing Buddy

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching