Dimensions of the Replacement Bearing Buddy Bras # BB19B

Question

Question:

Can you provide me the length and Inside Diameter for P/N BB19B, Grease caps by Bearing Buddy. Your data only shows outside diameter.

asked by: Kevin

0

Expert Reply:

I went and pulled the Replacement Bearing Buddy Bras # BB19B from our warehouse to get the dimensions you requested and found them to be 2.07 inches from the inside of the cover and 1.29 inches deep.

expert reply by: Jameson C

0

Answer 1

Replacement Bearing Buddy Bras - Model 19B #BB19B are a strong candidate for the right fit. They fit models 1980, 1980SS, 1980A, 1980A-SS, 1938, 1938SS, 1968, 1968SS, 2047, 2047SS, 2080 and 2080SS. The outer diameter of the bra is 2-1/8 inches…

view full answer...

Answer 2

It sounds like you are looking for the Bearing Buddy coverbra #BB19B. The closest Bearing Buddy sizes that are close to the 2 inches that you measured are either 1.98 inches or 2.047 inches. The Bearing Buddy #BB17B you referenced are too small for…

view full answer...

Answer 3

Since you said the outer diameter of the Bearing Buddy you have now is 2-1/8 inch the correct replacement bra for it is the part #BB19B.

view full answer...

Answer 4

Most likely the correct replacement bearing buddy bra that you would need is the part #BB19B which has an outer diameter of 2-1/8 inches. Part #BB17B has an outer diameter of 2 inches, and part #BB23B has an outer diameter of 2.441 inches (this…

view full answer...

Answer 5

It sounds like you need a grease cap or bearing protectors. The Bearing Buddy Bra, #BB19B, that you referenced covers the Bearing Buddy Bearing Protectors, like part #BB1980A. In order to choose the correct grease cap or bearing protector, I…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Dimensions of the Replacement Bearing Buddy Bras # BB19B

Product Page this Question was Asked From

Continue Researching