Recommended Ball Mount for 2020 Ford F-250 Towing Car Trailer

Question

Question:

Hello, my job is to hauler cars, I have a F250 Ford HD TurboDiesel and I just bought a trailer that its capacity is 14000 lbs, I am not sure what ballmount to get, I would like a recommendation from you which would be the most useful for my type of work, thank you.

asked by: Abramo F

0

Expert Reply:

The B&W Tow & Stow 2-Ball Mount # BWTS20040B is what I recommend.

The B&W Tow & Stow is a very high quality hitch which has been time proven to be strong and reliable which is why I recommend it for towing your car trailer with your 2020 Ford F-250 Super Duty.

I included a video of the # BWTS20040B for you to take a look at.

expert reply by: Samuel C

0

Answer 1

There is a way for you to not only lock the B&W Tow & Stow 3-Ball Mount - Compatible with GM MultiPro Tailgate - 2.5" Hitch - 148K #BWTS20067BMP to your 2-1/2 inch trailer hitch, but also the ball platform to the mount, and the hitch…

view full answer...

Answer 2

For lubricating any lock, a dry lubricant like powdered graphite is recommended. Using grease and oil or spray lubricants like WD 40 can actually attract dirt and grime and make the lock cylinder sticky after a time.

view full answer...

Answer 3

I would love to help but I can't really tell you if you need the B&W Tow & Stow 2-Ball Mount with 5" Drop part #BWTS20037B (part #BWTS20037C) or 7" Drop part #BWTS20040B (part #BWTS20040C) as it varies by application so you will…

view full answer...

Answer 4

You can lock your B&W Adjustable Ball Mount #BWTS20040B using their matching 2-1/2-inch hitch lock #C23025. This pin lock also fits their chrome ball mount #BWTS20040C.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...