Rear Sharkfin Camera Mount Replacement For A Furrion Vision S RV Camera

Question

Question:

I have a FOS48TA-BL camera and screen but no mounting bracket. Is there a mounting bracket I can purchase that will allow me to put the camera in it and use it on my new trailer?

asked by: Geoff

0

Expert Reply:

Yes, the mounting bracket you need for your Furrion RV Camera System # FOS43TASF is the Replacement Shark Fin Camera Mounting Bracket for Furrion Vision S RV Camera Systems # FRCBRKT-BL. This shark fin shaped bracket provides a waterproof housing for the camera. and comes with the pig-tailed power cable to easily wire into your trailer.

expert reply by: Kevin C

0

Answer 1

Air bags (Air Lift) and upgraded jounce springs (SumoSprings) are both great options to reduce rear end sag and squat while towing or hauling. That said, if you started with air bags you would be let down with upgraded jounce springs because air…

view full answer...

Answer 2

The Replacement Shark Fin Camera Mounting Bracket #FRCBRKT-BL mounting holes are 3-11/16" apart from center to center of the holes. The body of the mount where the camera goes is only 3-1/4" wide. With the way the body forms around…

view full answer...

Answer 3

We do have the correct replacement antenna for your Furrion FOD43TA-BL camera system, with the correct part being the following: - Replacement Antenna for Furrion Vision 1, 2, and S Wireless RV Camera Systems #772577

view full answer...

Answer 4

The replacement antenna for the Furrion S back up camera system is Replacement Antenna for Furrion Vision 1, 2, and S Wireless RV Camera Systems part #772577.

view full answer...

Answer 5

We have the VueSMART RV Trailer Backup camera part #HM34FR that will display on a smartphone but the Furrion Vision S system like the part #FOS43TASF does not have a ability to display on smartphone.

view full answer...

Answer 6

Typically people run the power wire of camper cameras like the Furrion Shark Fin Mount part #FRCBRKT-BL to the running light circuit of the trailer wiring which allows you to turn the camera on easily inside the vehicle by turning on either the…

view full answer...

Answer 7

Furrion branded cameras are only compatible with Furrion branded monitors so you would need to use one of the follow monitor sizes to sync the camera too; Replacement 4.3" Monitor for Furrion Vision S Wireless RV Camera System #FR77FR.…

view full answer...

Answer 8

Since your trailer has the bracket #FRCBRKT-BL that would mean your trailer has the Furrion pre-wiring which is very common for newer RVs. The part #FOS43TASF is a fit for this and would be a really easy install. This gives you a monitor with a 4.3…

view full answer...

Answer 9

The Replacement Shark Fin Camera Mounting Bracket for Furrion Vision S RV Camera Systems - Black - Qty 1 #FRCBRKT-BL is the only way to get the Shark Fin Mount without replacing the entire camera.

view full answer...

Answer 10

It would be a good idea to go with different holes for the reinstallation of the deck boards on your trailer, or at least enlarge the ones you have and then go with the next thicker screws so that you know you are getting a good grip on the metal…

view full answer...

Answer 11

To drop the front of the pin box and thus lower the front of the fifth wheel, you'd need to RAISE the pin box, not lower it. Lowering the pin box would raise the height of the fifth wheel at the front. If you have an available set of holes at the…

view full answer...

Answer 12

When adjusting the height of a pin box such as #LC1191191 it is important to support the pin box when removing the bolts. I recommend 2 or 3 buddies to give you a hand and make sure no one is beneath the pin box while raising or lowering it. With the…

view full answer...