Will Ultra-Fab Power Twin II Electric Stabilizer Work on 2021 Forest River R-Pod 202

Question

Question:

will this leveling system work on my 2021 Forest River R pod 202

asked by: Nathan H

0

Expert Reply:

Yes, your 2021 Forest River R-Pod 202 is absolutely compatible with the Ultra-Fab stabilizers, which are the following part:

- Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors # UF39-941705

This stabilizer has the proper width and more than enough capacity to work well with your travel trailer, and will give you a very easy way to level it out because of its independent motors. They operate independently, so even if you are on uneven ground you will be able to level and stabilize your R-Pod without issue.

I have added a link below to a video review for you to check out as well of the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors # UF39-941705.

expert reply by: Kyle S

0

Answer 1

We can get your stabilizer set up, and I can tell you where each of the four wires go for the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors #UF39-941705. I have added a cut out for you of the installation instructions which cover how…

view full answer...

Answer 2

A -frame jacks are not designed to be used to level a trailer side to side, but we do have something that would be a much better solution. The Ultra Fab kit part #UF39-941705 would be a great option. This attaches to the bottom of the frame of your…

view full answer...

Answer 3

For the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors #UF39-941705 that you referenced we do offer a replacement switch. I checked with Ultra-Fab to confirm and the correct part number is #UF17-101014. This is sold as a single switch…

view full answer...

Answer 4

The feet on the Power Twin stabilizer #UF39-941705 are each 8 x 5-3/4 inches.

view full answer...

Answer 5

To mount the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors #UF39-941705 you'll first want to determine your trailer's departure angle so that you can mount the jacks without having to worry about them hitting the ground when…

view full answer...

Answer 6

I spoke with my contact at Ultra-Fab and determined that the brackets that mount to the frame on the Power Twin II Electric Stabilizer, #UF39-941705, are 36 inches long.

view full answer...

Answer 7

The Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs #UF39-941704 measures 5" from the trailer frame to the lowest hanging part of the jack. I confirmed this with my contact at Ultra-Fab. Since your trailer has a lower profile it…

view full answer...

Answer 8

If you have the space to install 2 of the Power Twin stabilizers #UF39-941705 you certainly could. The brackets are 36 inches long. As long as there is less than 6,000 pounds on either the front or rear one then you would be within the capacity.…

view full answer...

Answer 9

The Ultra Fab Power Twin II Electric Stabilizer with Dual Motors #UF39-941705 that you referenced is designed for exactly what you are looking for so it would work well as long as your frame dimensions are compatible with it. If your trailer frame…

view full answer...

Answer 10

The Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers #PD4645V is exactly what you need for your Magnetek 7300. We have checked with Progressive Dynamics before and this is what they told us is needed. The DC fuse board does not…

view full answer...

Answer 11

The Lippert High-Speed Power Stabilizer Jack #LC298707 is a stabilizing jack which means it does not lift your trailer at all. The jacks are only meant to come down and press against the ground to stabilize the trailer so you don't feel the…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...