Replacement 6-Amp Stop Switch for Ultra-Fab Stabilizer Jack

Question

Question:

I need a stop switch 6amp for my stabilizer jack

asked by: J D

0

Expert Reply:

For the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors # UF39-941705 that you referenced we do offer a replacement switch. I checked with Ultra-Fab to confirm and the correct part number is # UF17-101014. This is sold as a single switch so you will need to order two to equip both side of your stabilizer.

expert reply by: Adam R

0

Answer 1

You can run the mounting bolts of the Ultra Fab Stabilizer Jacks #UF39-941705 up from the bottom or down through the top. Whichever works best. You wouldn't want to submerge the switches under water but they will easily survive rain and normal…

view full answer...

Answer 2

To mount the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors #UF39-941705 you'll first want to determine your trailer's departure angle so that you can mount the jacks without having to worry about them hitting the ground when…

view full answer...

Answer 3

The feet on the Power Twin stabilizer #UF39-941705 are each 8 x 5-3/4 inches.

view full answer...

Answer 4

A -frame jacks are not designed to be used to level a trailer side to side, but we do have something that would be a much better solution. The Ultra Fab kit part #UF39-941705 would be a great option. This attaches to the bottom of the frame of your…

view full answer...

Answer 5

I spoke with my contact at Ultra-Fab and determined that the brackets that mount to the frame on the Power Twin II Electric Stabilizer, #UF39-941705, are 36 inches long.

view full answer...

Answer 6

We can get your stabilizer set up, and I can tell you where each of the four wires go for the Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors #UF39-941705. I have added a cut out for you of the installation instructions which cover how…

view full answer...

Answer 7

The Ultra Fab Power Twin II Electric Stabilizer with Dual Motors #UF39-941705 that you referenced is designed for exactly what you are looking for so it would work well as long as your frame dimensions are compatible with it. If your trailer frame…

view full answer...

Answer 8

Yes, your 2021 Forest River R-Pod 202 is absolutely compatible with the Ultra-Fab stabilizers, which are the following part: - Ultra-Fab Power Twin II Electric Stabilizer with Dual Motors #UF39-941705 This stabilizer has the proper width and more…

view full answer...

Answer 9

The Ultra-Fab Power Twin II Manual Stabilizer for Trailers and RVs #UF39-941704 measures 5" from the trailer frame to the lowest hanging part of the jack. I confirmed this with my contact at Ultra-Fab. Since your trailer has a lower profile it…

view full answer...

Answer 10

The Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers #PD4645V is exactly what you need for your Magnetek 7300. We have checked with Progressive Dynamics before and this is what they told us is needed. The DC fuse board does not…

view full answer...

Answer 11

The Lippert High-Speed Power Stabilizer Jack #LC298707 is a stabilizing jack which means it does not lift your trailer at all. The jacks are only meant to come down and press against the ground to stabilize the trailer so you don't feel the…

view full answer...

Answer 12

If you have the space to install 2 of the Power Twin stabilizers #UF39-941705 you certainly could. The brackets are 36 inches long. As long as there is less than 6,000 pounds on either the front or rear one then you would be within the capacity.…

view full answer...

Replacement 6-Amp Stop Switch for Ultra-Fab Stabilizer Jack

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching