Fascia Trimming for Trailer Hitch C12057 for a 2013 Jeep Compass Sport

Question

Question:

Is there bumper trimming involved when installing this receiver hitch on my 2013 Jeep Compass? Anything else that might need to be done to make it fit?

asked by: Les B

0

Expert Reply:

There is minor fascia trimming required to install Curt trailer hitch # C12057 on your 2013 Jeep Compass. I have included a picture that comes from the instructions showing the area that needs to be trimmed. I have also linked the instructions for you to view.

Instead of the Class II hitch you're looking at I recommend the Class III # C13081. The 2 inch receiver opening of the Class III accepts a lot more accessories than the Class II. The Class III also makes sure you get all of the towing capacity out of your Jeep.

If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.

If the ball mount kit does not have the right rise or drop to tow the trailer level, use the link I have included that explains how to measure to choose a ball mount to tow the trailer level.

For trailer wiring use # 118539. I have linked the wiring instructions as well.

expert reply by: Michael H

0

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 4

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has…

view full answer...

Answer 5

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 6

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 7

The main difference between a Class III hitch and a Class IV hitch is the capacities they set for the hitches. Class III hitches are rated for up to 6,000 lbs GTW with 600 lbs TW whereas a Class IV is rated for up to 12,000 lbs GTW and 1,000 TW.…

view full answer...

Answer 8

For your 2024 Toyota RAV4, the best trailer hitch receiver that will fit is the following: - etrailer Trailer Hitch Receiver #e23ZR The #e23ZR is the best because it has completely concealed crosstube so only the receiver is showing, allowing your…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Yes, a trailer that is nose up can cause big problems. A level trailer is ideal and worth working toward for safety. The good news is that you can get the trailer almost exactly level with switching ball mounts. This is where an adjustable ball mount…

view full answer...

Answer 11

The B&W Tow and Stow ball mount #BWTS10049B will have some great features. You can stow the mounting platform that has the 3 hitch balls (1-7/8, 2, and 2-5/16 inch) underneath your vehicle. This is nice because you will eliminate the possibility…

view full answer...

Answer 12

I recommend using the Curt Lock Set #C23556 for your Curt Adjustable 2-Ball Mount #C99NR. This comes with a lock for the hitch receiver and one for the ball mount platform. Even though your platform uses 2 pins, only 1 locking pin is needed to secure…

view full answer...

Fascia Trimming for Trailer Hitch C12057 for a 2013 Jeep Compass Sport

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching