Is There a Lift Kit for a Jayco Jay Feather EXP 213 Trailer

Question

Question:

Seeking out which lift kit would work for this make and model. Looking for around 3inch of lift. Appreciate the help! Tandem Dexter Axle. From the imprint: Mod 10H SLR 13.3. 3000# capacity each.

asked by: Winton

0

Expert Reply:

The Jayco Jay Feather EXP 213 likely uses a Dexter Torflex #10 Axle. If that is the case, then you can use the Torflex Lift Kit part # K71-707-02 to lift the trailer 2-5/8". This should be a direct bolt-on kit with cutting or welding.

expert reply by: Conner L

0

Answer 1

Torflex Lift Kit - Tandem Axle - 2-5/8" Lift Item #K71-707-02 doesn't require that you have your axles aligned after installation but it is good practice to do so. It is actually easier than you might think. Basically, measure from…

view full answer...

Answer 2

The most cost effective option I have for you would be to install a 1" taller hanger. I have linked a page that will display all of our leaf spring hangers for you. The only thing you will want to do is measure your current hangers and…

view full answer...

Answer 3

How you would proceed will depend on which type of suspension your camper has, and who the manufacturer of the axle was. If it's a leaf spring axle, and the leaf springs are currently mounted to the underside of the axle, you can use an…

view full answer...

Answer 4

When installing the Torflex Lift Kit #K71-707-02 for the #10 Dexter axles on your 2022 Forest River Rockwood Mini Lite travel trailer you will want to follow the manufacturer instructions for raising your entire trailer off the ground. This is…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 10

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 11

Increasing the tire and wheel size can increase the height of the trailer but it's usually quite minimal. Before you do anything else you should see if the pin box can be adjusted. Although you have to be careful here since This will lower the…

view full answer...

Answer 12

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...