Which TorkLift Rear Camper Tie-Downs Fit 2008 Chevy Silverado 2500HD W/ TorkLift SuperHitch Receiver

Question

Question:

Will Torklift rear tie down TLC3209 fit my 2008 Chevy 2500HD with a Super Hitch TLC1206 installed?

asked by: Wayne M

0

Expert Reply:

I have another option for you, but the TorkLift Custom Frame-Mounted Camper Tie-Downs - Rear # TLC3209 you were looking at are only confirmed to fit 2007-2010 Chevrolet/GMC 2500 trucks with the factory trailer hitch receiver.

Since your 2008 Chevrolet Silverado 2500HD has the TorkLift Super Hitch Original Trailer Hitch Receiver # TLC1206 installed you will need to go with the # TLR3500 instead.

I included a few videos of the products mentioned for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 5

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 6

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 7

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 8

There is no weight capacity for the Brophy Clamp On Camper Tie-Downs #HSSF. The tie-down hardware kit #TDHP, that is used to secure the camper to the #HSSF tie-downs has a weight capacity of 3,000-lbs. My contact at Brophy said the tie-downs will…

view full answer...

Answer 9

Yes you can absolutely use the HappiJac Qwik-Load Turnbuckles for Camper Tie-Downs #LC182895 with your TorkLift tie downs.

view full answer...

Answer 10

That is correct, you can tap into the plug and it will provide a charge but keep in mind that this is not the most efficient way for charging a battery. This method does not provide any charge balancing or battery charge management and on newer…

view full answer...

Answer 11

You do not need to remove the bed of your truck to install the HappiJac part #LC182906-182971 that you referenced. I found a copy of the install instructions for this part number (see attached pictures) and there's no mention of the bed needing…

view full answer...

Answer 12

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...