Can Reese 83660 Friction Sway Control Be Used on Both Sides of Trailer Frame

Question

Question:

when using two of these is there a left and right or do you take this apart to alter for dual application.

asked by: Jim G

0

Expert Reply:

There isn't a left and a right. The unit is set up for the right side of the trailer, when adding a second, you'll turn the lever to the 'off' position, loosen the adjustment bolt and slide out and flip the slide bar so the socket is at the bottom. This will allow the Reese # 83660 Friction Sway control to be used on the left side of the trailer.

I've linked to a product description video that you might find helpful.

expert reply by: Mike L

0

Setting Up 83660 For Left Hand Side of Trailer
(click to enlarge)

Answer 1

No you should not have constant power on the brake output pin, the blue wire should only have power with the brake pedal depressed in the vehicle or the brake controller manual override is activated. If the blue wire has a constant 12V then it is an…

view full answer...

Answer 2

The speed rating should be on the sidewall of your tires unless it is the standard 65 mph max. The letter represents the following maximum: J=63 mph L=75 mph M=81 mph N=87 mph For your tires, I recommend the Taskmaster 5.30R12 Radial Trailer Tire -…

view full answer...

Answer 3

Yes, all of the friction sway control units we carry can be fitted to either the left or right hand side of a trailer. The #83660 that you referenced is setup out of the box ready for the passenger side of a trailer. All you would need to do is pull…

view full answer...

Answer 4

If your flip-down tongue jack is mounted on the outside of your trailer frame, you will not be able to mount the Reese Friction Style Sway-Control System, part #83660, on the same side. The friction sway-control system will mount to the frame of the…

view full answer...

Answer 5

For the Curt Friction Sway Control for Weight Distribution Systems #17200 you will remove the inner arm and spin it 180 degrees, then reinsert into the friction sleeve. This will allow the sway control to be used on the drivers side of your travel…

view full answer...

Answer 6

All you would need to add a second sway control arm to Curt weight distribution system #C17322 is friction sway control kit #83660 or #17200. These bars do not have a left and right, you just have to take out the inside, turn it over, and put it back…

view full answer...

Answer 7

Since friction sway control bars, like the Reese #83660, already fit both left and right side manufacturers have not created one that is specifically for the left hand side. You will need to have another Sway Control Tab #3442 professionally welded…

view full answer...

Answer 8

Curt actually makes the etrailer.com hitches like the part #e98908 that you referenced which is why it's basically identical to the Curt #C13309 that fits your 2018 Nissan Pathfinder. It is a somewhat new hitch line we started offering but not…

view full answer...

Answer 9

You can use the Curt Ball Mount with Sway Control Bracket, #D320, in the rise position to have the sway control bracket on the left side, but you will want to remember that doing this will raise the height of your trailer tongue by almost 3 inches.…

view full answer...

Answer 10

The trailer hitch that I recommend for a 2019 Nissan Pathfinder is the etrailer Trailer Hitch Receiver part #e98908 because it features an easy bolt-on install and has a hidden design so you don't have to look at a bulky crosstube on the back of…

view full answer...

Answer 11

Is there anything on the other side of the trailer frame? If not, you could just run the Reese Sway Control part #83660 on the other side of the trailer and you would be good to go. You would just need to loosen the sway control unit enough that you…

view full answer...

Answer 12

Brake controllers such as the P3 you referenced #90195 will go into a sleep mode after about 15 minutes of it sensing no movement. If you peek through the window after 15 minutes then it should be in sleep mode. Opening the door or causing movement…

view full answer...